Question: Q 4 : Find the reaction forces at support A and support B and draw the shear force diagram and bending moment diagram for the

Q4: Find the reaction forces at support A and support B and draw the shear force diagram and bending moment diagram for the following beam. The value of your Uniformly Distributed Load (UDL) and distances is provided in Table 1.
100%
Table 1 has: X =2.25kn/m, a2=1.05m
Can you give all working as i am stuck
Q 4 : Find the reaction forces at support A and

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Suppose you purchase a part from a supplier for a unit cost of $ 4 with which you assemble red widgets. On average, you use 50,000 units of this part each year. Every time you order this particular...

Q:

Draw shear force and bending moment diagrams for the following beam. Find the maximum shear force (in magnitude) and maximum bending moment (in magnitude), as well as their locations. 1 Draw FBD 2...

Q:

Problem 1 A beam AB is clamped at one end and joined to a bar, BC, at the other end by a hinge. The bar is pinned at end C. The length of the beam is L while the length of the bar is L/2. The beam...

Q:

Given the T-beam and cross-section shown in the figure below: a. Draw the overall free body diagram for beam b. Find the reaction forces at points A and B c. Draw the shear and moment diagram for the...

Q:

Problem 1. The beam is loaded by the centered point force P. The supports on both sides are full cantilever supports. The beam has modulus E and cross-sectional moment of inertia I. Determine the...

Q:

g) h) 5 KN 50 mm 20 mm 150 mm 40 mm 2 kN 200 mm 5 kN 1 kN Three forces are applied to member ABD as shown. The cross-section is a hollow rectangle with 20mm height and 40mm width and a wall thickness...

Q:

Figure Q1 shows an overhanging beam of ABCD that is being supported at pin B and D. Answer the following questions: iii. i. Sketch free body diagram and find the forces at pin B and D. (3 marks) ii....

Q:

Given a distributed load w = 6N/m is applied to the beam, that is support by a wall A. A clockwise-moment M = 12N -m is applied to point B. If a = 5m, draw the shear force and bending moment diagram....

Q:

a: b: b) Draw the bending moment diagram. 150 100 gz N 50 -50 A a b B 1 2 3 4 6 7 8 -100 -150 A: B: a: b: 9 10 10 11 & + 12 - -

Q:

a. Why can the support at A be considered only to provide a vertical reaction force in contrast to B where all three directions are restrained? (3 marks) b. Using the modelling assumptions described...

Q:

Figure Q1 shows an overhanging beam with pin support at point A and roller support at point B. The beam is subjected to uniformly distributed load from point A to point B and concentrated load at...

Q:

Problem 1 The position of a particle along a straight line is given by s= (t3-15t2 + 9t+c) ft, where t is in seconds and c is the last two digits of your registration number. Determine its maximum...

Q:

Ford Motor Company filed an Amendment No. 1 on Form 10-K/A ("Amended 10-K") to its Annual Report on Form 10-K for the year ended December 31, 2017 ("Original 10-K") filed with the U.S. Securities and...

Q:

1 1 . Which of the following is true about tax expenses reported on the income statement of U . S companies? a ) a . It only includes tax payable this year b ) It is sum of tax payable this year plus...

Q:

Which of the following is NOT a limitation of the statement of financial position? O a. Many assets are reported at historical cost. O b. Judgements and estimates are used. O c. All pertinent...