Question: Q.3 Determine the length (L) and width (W) in meter for a single tray gravity settler of height (H) 1 m to remove all the

Q.3 Determine the length (L) and width (W) in meter for a single tray gravity settler of height (H) 1 m to remove all the iron particulates from a dust-laden gas stream with the data given as: dp = 50m uniform; Q = 7.5 m3/s; p =8.00 g/cc, gas inlet velocity = 2 m/s. Consider the viscosity of gas is 1.81 kg/m s.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Chemical Engineering Questions!

The management team of Lisas Linens & Furniture is considering the following capital projects: Project Cost Annual cash flows Years New manufacturing plant 20,000,000SAR 310,000SAR 13 Machinery...

I need help with this lab. Please answer questions for pages 4-7. Freefall Purpose: We will measure the value of 'little g', or the acceleration due to gravity on the surface of Earth. The particular...

(13%) Problem 1: One kind of cuckoo clock keeps time by using a mass bouncing on a spring, usually something cute like a cherub in a chair. DA What is the force constant, in newtons per meter, needed...

ONLY THE ONES THAT ARE CIRCLED Answer ASAP please Problems Answers to problems marked with an asterisk are given at the end of the text. Section 1.1 1. Make sure you know how to start and quit a...

Given the following beam of overall length \ ( L \ ) and where the centre support is located at \ ( L / 2 \ ) , determine the length \ ( L \ ) that would result in the slope of the beam being equal...

Afence around a eld is shaped as shown in Figure P25. It consists of a rectangle of length L and width W and a right triangle that is symmetric about the central horizontal axis of the rectangle....

SHOW WORK AND CALCULATIONS FOR EACH QUESTION 1) Determine the length of the hypotenuse for the right triangle shown, if a=16cm and b=8cm. Use Units 2) Determine the area of triangle ABC, if a=3m and...

Q5 (Bonus 10 Points) The column shown in the figure is centrically loaded hot-rolled steel member with pin connected at ends for both buckling plans. Determine the length ( L ) for which the column (...

The formula L = U(R + H) is used to determine rafter length (L) of a roof, where R is the run and H is the overhang. The quantity U represents unit line length. When the run and the overhang are in...

A rectangular sedimentation basin is designed with a water depth ( D ) of 3 m and the L to W ratio is 4 : 1 . The design flow rate is 5 4 m 3 h r and the design residence time is 0 . 5 hr . Ans: ( a...

Test for normality at the 1% level using a sample of n = 79 (rounded) values x (tensile strength [kg/mm 2 ] of steel sheets of 0.3 mm thickness). a = a(x) = absolute frequency. (Take the first two...

Structure No. 7: 100 B0 30 52 20- 60 70 90 100 Neat Liquid 3075 1649 2974 1448 2918 856 1773 Carbon 13 NMR: 134.91 (s) 111.64 (d) 22.85 (g) 18.16 (g) 6H (two 400 MHz singlets (CDCI,) 1H (s) 7 6 4 ppm...

Material is being moving from one place to another place using a crane then what will be position of boom and hoist ( load ) ? 1 . boom down and hoist down 2 . boom up and hoist down 3 . boom up and...

3 Kai works as a currency exchange trader in the train station of a major city. There are many buyers and sellers in the market for exchanging currencies; no one of them can affect the market; all...

The interest in developing know-how, often through foreign sources, has led to the development and uptake of training in HRM through the universities and through foreign companies.

The entry of foreign organizations with more attractive compensation packages and work is also causing problems of retention in state-owned and justprivatized organizations, and there is a need to...

Pay and benefits. Evidence suggests a significant departure from the old centralized mode, particularly for managers, professionals and technicians, with pay for clerical and manual workers still...