Question: In an epicyclic gear train, an arm carries two gears 1 and 2 having 40 and 50 teeth respectively. The arm rotates at 160

In an epicyclic gear train, an arm carries two gears 1 and

In an epicyclic gear train, an arm carries two gears 1 and 2 having 40 and 50 teeth respectively. The arm rotates at 160 rpm ccw about the center of gear 1, which is fixed. 1) Predict the speed of the gear 2. 2) Analyze the performance of this mechanism if the arm speed reduced to 110 rpm.

Step by Step Solution

★★★★★

3.44 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Solution Given that epicyclic gear train Here Gear 1 Input Gear Driving Gear 2 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Maize has the following budgeted income statement: 24, 000 Units Sales $ 360, 000 Less variable costs: Manufacturing costs 192, 000 Selling and administrative costs 96, 000 Contribution margin $ 72,...

Two vertical cylindrical tanks 1 and 2 having diameters 3m and 4m, respectively are connected with a 200 mm diameter tube at its lower portion and having C = 0.60. When the tube is closed, the water...

Arm ACB rotates about point C with an angular velocity of 40 rad/s counterclockwise. Two friction disks A and B are pinned at their centers to arm ACB as shown. Knowing that the disks roll without...

The mechanism train shown consists of an assortment of gears and pulleys to drive gear 9. Pulley 2 rotates at 1200 rev/min in the direction shown. Determine the speed and direction of rotation of...

The speed ratio of a reverted gear train is to be 15. The module of gears 1 and 2 is 3 mm and thatof gears 3 and 4 is 2.5 mm. Calculate the suitable number of teeth for the gears. The centre...

Question: Assignment #3: Independent Samples T test Conduct an Independent Samples T test to answer the questions based on the following scenario. (Assume a nondirectional research hypothesis (two...

REFERENCE : https://www.shrm.org/ Answer the case study questions 1 and 2 that are highlighted in yellow Task: You have been hired as a consultant by the owner to identify specific performance and...

Repeat Problem 5. Assume that the shaft connecting gears 1 and 2 is relatively short and rigid. Data From Problem 5: A three-degree-of-freedom gear-train system is shown in Figure 5.101, which...

A three-degree-of-freedom gear-train system is shown in Figure 5.101, which consists of four gears of moments of inertia $I_{1}, I_{2}, I_{3}$, and $I_{4}$. Gears 2 and 3 are meshed and their...

Intermediate: Preparation of cash budgets A company is to carry out a major modernization of its factory commencing in two weeks time. During the modernization, which is expected to take four weeks...

Suppose a retailer has two markets, 1 and 2. demand 1 follows normal distribution with mean 100 and standard deviation 12.4. demand 2 follows normal distribution with mean 110 and standard deviation...

Verde Company produces wheels for bicycles. During the year, 330,000 wheels were produced. The actual labor used was 180,000 hours at $9.25 per hour. Verde has the following labor standard: 0.5 hour...

Let P be a point on a ladder of length a + b, P being a units from the top end. As the ladder slides with its top end on the y-axis and its bottom end on the x-axis, P traces out a curve. Find the...

Which of the following is TRUE regarding miscellaneous itemized deductions exceeding 2 % of AGI? Such amounts were deductible in 2 0 1 7 Tax preparation fees are deductible Safe deposit box fees are...

A piston/cylinder has a water volume separated in V A = 0.2 m 3 and V B = 0.3 m 3 by a stiff membrane (Fig. P3.211). The initial state in A is 1000 kPa, x = 0.75 and in B it is 1600 kPa and 250C. Now...

A piston/cylinder has a water volume separated in V A = 0.2 m 3 and V B = 0.3 m 3 by a stiff membrane similar to the one in Fig. P6.128. The initial state in A is 1000 kPa, x = 0.75, and in B it is...

Compute the weakest precondition for each of the following selection constructs and their postconditions: a. if (a == b) b = 2 * a + 1 else b = 2 * a; {b > 1} b. if (x

Refer to the Baseball 2018 data, which report information on the 30 Major League Baseball teams for the 2018 season. Set up a variable that divides the teams into two groups, those that had a winning...

The United States consistently imports much more than it exports. The annual gap is consistently several hundred billion dollars. Does this concern you? If so, what should be done about it? If not,...

Look at the ellipse and its properties: An ellipse has two foci. Only one focus is pictured in the illustration, since the sun only occupies one of the two foci. The line through the two foci that...

ca 011/ An epicyclic gear train shown in figure, the arm is keyed to the same shaft as the bad drum and the wheel A is keyed to the second shaft which carries a chain wheel, the chain being operated...

An epicyclic gear train consists of sun wheel S, a fixed internal gear E and three identical planet wheels P carried on a star-shaped planet carrier C, as shown in Fig. 15.20. The planets rotate at...

Figure P3.32 illustrates an epicyclic gear train driven by the arm, link 2, with an angular velocity 2 = 3.33 rad/s cw and an angular acceleration 2 = 15 rad/s 2 ccw. Define point E as a point on the...

A compound epicyclic gear train is shown in Fig.15.48 The gears $A, D$ and $E$ are free to rotate on axis $P$. The compound gear $B$ and $C$ rotate together on axis $Q$ at the end of arm...

A compound epicyclic gear train is shown in Fig. 15.28. The gears A, D and E are free to rotate on the axis P. The compound gear B and C rotate together on the axis Q at the end of arm F. All the...

In an epicyclic gear train shown in Fig. 15.45 the number of teeth on gears $A, B$ and $C$ are 50, 25 and 55 respectively. The arm rotates at $450 \mathrm{rpm}$ clockwise. Calculate (a) the...