Question: Question 1 A full journal bearing is required for a shaft rotating at 1450 rpm. The lubricant can be supplied at an inlet temperature of

Question 1 A full journal bearing is required for a shaft rotating at 1450 rpm. The lubricant can be supplied at an inlet temperature of 60oC using an available cooling system. 1.1 Determine the overall temperature rise in the bearing. 1.2 Determine the flow rate of lubricant required. 1.3 Establish that the selected design lies within the optimum zone for minimum friction and maximum load on the minimum film thickness ratio chart. Assume the following: Lubricant is SAE 10 L/D ratio of unity. Shaft nominal diameter = 40 mm. Load on the bearing = 2100 N.

Show all the calculations and state all the assumptions.

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

11 Determining the overall temperature rise in the bearing Given Shaft rotation speed N 1450 rpm Inlet lubricant temperature Ti 60C Assumptions The lu... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Do you think ethics can be taught? Why is this a difficult question to answer?

A full journal bearing is 25 mm long. The shaft journal has a diameter of 50 mm with a unilateral tolerance of 0.01 mm. The bushing bore has a diameter of 50.05 mm with a unilateral tolerance of 0.01...

A full journal bearing has a shaft diameter of 80.00 mm with a unilateral tolerance of 0.01 mm. The l/d ratio is unity. The bushing has a bore diameter of 80.08 mm with a unilateral tolerance of 0.03...

A full journal bearing has a journal with a diameter of 2.000 in and a unilateral tolerance of 0.0012 in. The bushing has a bore with a diameter of 2.0024 and a unilateral tolerance of 0.002 in. The...

A full journal bearing is required for a shaft rotating at 1450 rpm. The lubricant can be supplied at an inlet temperature of 60 oC using an available cooling system. 1.1 Determine the overall...

Bearings Lecture No.4 Home Work Sheet 8.ZA no lis 1 8.1 A plain surface bearing has been partially specified to support a load of 2000 N at a rotational speed of 20 rpm. The nominal diameter of the...

QUESTION EIGHT A full journal bearing has a nominal diameter of 5 0 . 0 mm and a bearing length of 2 5 . 0 mm . The bearing supports a load of 3 0 0 0 N , and the journal design speed is 3 0 0 0 rpm...

Question 1 [ 2 5 ] A full journal bearing has a nominal diameter of 3 0 m m and a bearing length of 3 0 m m . The bearing supports a load of 2 0 0 0 N , and the journal bearing's speed is 1 8 0 0 r p...

A full journal bearing has a nominal diameter of 8 0 . 0 mm , bearing length 6 0 . 0 mm . The bearing supports a load of 7 5 0 0 N , and the journal design speed is 8 0 0 rpm . The radial clearance...

hi could you help me with these questions? I have to do journal entries and multiple questions. Question 1. Floppy Company's December 31, 2014 trial balance is as follows: Floppy Corporation Trial...

Q . 2 . A 2 5 - mm long full journal bearing having diameter of 5 0 mm runs at 6 0 0 rpm , and has a radial clearance of 0 . 0 2 cm . The SAE 4 0 oil supply is used and coefficient of friction of the...

A fixed quantity of gas at 21oC exhibits a pressure of 752 torr and occupies a volume of 5.12 L. (a) Calculate the volume the gas will occupy if the pressure is increased to 1.88 atm while the...

Soonerco has net operating income of $2.5 million per year, and $15 million of debt outstanding with a required return (interest rate) of 8 percent. The required rate of return on assets in this...

Let f left parenthesis x , y right parenthesis equals x squared minus 3 xy minus y squared . Compute f left parenthesis 2 , 0 right parenthesis and f left parenthesis 2 , negative 5 right parenthesis...

A water cooler supplies an office with drinking water needs. The cooler is cooling water from 28 to 5C at an average rate of 14 kg/h. If the COP of this refrigerator is 2.4, the required power input...

Hot water usage for a house cost per year is $34 that is supplied by an 85 percent efficient electric heater at an electricity rate of $0.08/kWh. If the water is heated from 25 to 60C, the amount of...

Identify the advantages and disadvantages of using two of the following in comparing investments: accounting rate of return, net present value, payback period, and internal rate of return. Which one...

The Laguerre polynomials L, (x) are polynomial solutions to Laguerre's equation. xy" + (1- x)y' + ny = 0 The Laguerre polynomials satisfy Rodrigues's formula. ex dn Ln (x) = (x"e -x), for n= 0, 1, 2,...

Find a minimum value for the radius of convergence of a power series solution about xp. y" - 5xy' - 2y = 0; xp = 3 Select the correct answer below and, if necessary, fill in the corresponding answer...

6 Theory of Machines 5. A shaft carries five masses A, B, C, D and E which revolve at the same radius in planes which are equidistant from one another. The magnitude of the masses in planes A, C and...

For the bolted assembly of Prob. 829, it is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a...

For the shaft application defined in Prob. 379, p. 139, the input shaft EG is driven at a constant speed of 280 rev/min. Obtain a Basic Load Rating for a cylindrical roller bearing at A for a life of...

For the handle in Prob. 380, one potential failure mode is twisting of the flat plate BC. Determine the maximum value of the shear stress due to torsion in the main section of the plate, ignoring the...

Using problems to drive improvement requires the right culture, customer recovery, process recovery and staff recovery.

Service recovery is the action of seeking out and dealing with problems and failures in the provision of service in order to improve the service and operational and organisational performance.

How can belief bias (the tendency to accept conclusions based on how believable those conclusions are, rather than based on whether they are logically valid) be influenced by others? How could a...