Question: Question 2 a) Verify whether the strength of a single equal leg angle L 120 10 mm in tension connected on one side via

Question 2 a) Verify whether the strength of a single equal leg

Question 2 a) Verify whether the strength of a single equal leg angle L 120 10 mm in tension connected on one side via one line of two M16 (d=16mm) bolts in standard holes (d,-17mm) as shown in Figure (3), (dimensions in millimeters). Bolts connect only one side of the angle to a gusset plate. The angle is subjected to a design axial load Nt,Ed of 350 KN. 60 70 50 Figure (3) CR, 8 c) Any steel structure is an assemblage of different members or sections, which are connected to one another at its ends, using connections. Facilitate the flow of forces and/or moments from one member to another and also used to extend lengths of different members. Discuss the following connections: 1) Bolted connection II) Welded connection

Step by Step Solution

★★★★★

3.35 Rating (158 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Solutions since it is a lug angle it will follow shear lag effect 06 for ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

The three-member frame is connected at its ends using ball-and-socket joints. Determine the x, y, z components of reaction at B and the tension in member ED. The force acting at D is F. Given: F =...

Two sticks as shown in figure 3 are being held to stand on the floor with a little inclination. When the sticks are released, the stick without an added weight on its top end rotates to the floor...

The bolted connection shown in the figure is subjected to a tensile shear load of 90kN. The bolts are ISO class 5.8 and the material is cold-drawn AISI 1015 steel. Find the factor of safety of the...

A heat sink for cooling computer chips is fabricated from copper (k s = 400 W/m' K), with machined micro channels passing a cooling fluid for which T = 25C and h = 30,000 W/m 2 K. The lower side of...

The forces and couple moments which are exerted on the toe and heel plates of a snow ski are Ft, Mt, and Fh, Mh, respectively. Replace this system by an equivalent force and couple moment acting at...

Find the numbers such that the average value of f(x) = 2 + 6x 3x2 on the interval [0, b] is equal to 3.

A long trapezoidal bar is subjected to uniform temperatures on two surfaces, while the remaining surfaces are well insulated. If the thermal conductivity of the material is 20 W/m K, estimate the...

Writing Improvement Exercise: Direct Openings Your Task. Revise the following openings so that they are more direct. Add information if necessary. a. Alliance Associates has undertaken a management...

Repeat Prob. 625 for a load that fluctuates from 12 kN to 28 kN. Use the Modified Goodman, Gerber, and ASME-elliptic criteria and compare their predictions. Repeat Prob. 625, The cold-drawn AISI 1040...

A 20-cm-long hollow nichrome tube of inner diameter 2.8 mm, outer diameter 3.0 mm is connected, at its ends, to a 3.0 V battery. What is the current in the tube?

Demonstrate your understanding of these terms by using them correctly in a paragraph you create. Creativity is encouraged, but not required; a realistic scenario would be best. Do not simply provide...

Humphrey Enterprises is a public company located in Toronto that follows IFRS and has a December 31 year end. It is involved in the manufacturing of pet supplies that are distributed and sold all...

A robot force control system with unity feedback has a loop transfer function [6] L(s) = KG(s) = K(s + 2.5) (s2 +25+2)(s2 + 4s +5)* (a) Find the gain K that results in dominant roots with a damping...

During January 2020, the Fair Work Commission1 commenced an investigation into Defiant Ltd for underpayment of wages. The Fair Work Commission is expected to deliver its decision in October 2020....

A jet of water 80 mm diameter and has a velocity of 20 m/sec striking at the center of the hemispherical vane. The liner velocity of the vane is 10 m/sec. in the direction of jet. Find the force...

The United States of America recently initiated what was seen as an act of aggression on Iran. Discuss the basis of this move and present your arguments as a student of International relations...

Diamond Company is considering purchasing a machine that would cost $756,000 and have a useful life of 8 years. The machine would reduce cash operating costs by $132,632 per year. The machine would...

1 pts Next An endometrial biopsy can be done in the office setting. It has a accuracy in diagnosing endometrial cancer. Low overall O Average O High None of the above; it is not a good test for...

watch the three short clips below then answer the questions Copy and paste the three links below 1) Projectile Motion https://www.nsf.govews/mmg/mmg_disp.jsp?med_id=72205&from= 2) Newton's Second Law...

E-Physics Tutorial Book Note: I have attached below the lesson for the 3 activities. Thank you so much for your time and effort. Activity 1. Directions: Use the right-hand rule to determine the...

Let A, B be sets. Define: (a) the Cartesian product (A B) (b) the set of relations R between A and B (c) the identity relation A on the set A [3 marks] Suppose S, T are relations between A and B, and...

AN ARBITRATOR'S DILEMMA: BULLYING OR SELF-PRESERVATION ? INTRODUCTORY NOTES According to Namie (2000), one in every five United States employees was bullied with repeated, deliberately harmful verbal...

Briefly describe ASCII and Unicode and draw attention to any relationship between them. [3 marks] (b) Briefly explain what a Reader is in the context of reading characters from data. [3 marks] A...

DAVID DOESN'T DELEGATE Overcoming an Individual's Immunity to Change AS ANY EXPERIENCED MANAGER will tell us, being an effective delegator is crucial to using everyone's time, skills, and knowledge...