Question: Question 2 The lap joint is fastened with four 3 / 4 - in , - diameter rivets. The working stresses are 1 4 ksi

Question

2

The lap joint is fastened with four

3 / 4 -

, -

diameter rivets. The working stresses are

14

ksi for the rivets in shear and

18

ksi for the plates in bearing. Find the maximum safe axial load p that can be applied to the joint. Assume that the load is equally distributed among the rivets. The magnitude of force

P

in kips when shear stress in rivets governs. show solution and show proper how to input in calculator

Question 2 The lap joint is fastened with four 3

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

6. What is the magnitude of charge on a particle that is moving at 3.6 x 106 m/s and experiences a magnetic force of 1.2 x 10-10 N when it encounters a magnetic field of 3.0 T? a. What are the...

1.55 The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that...

Question 6 The lap joint is fastened with four 3 4 - in . - diameter rivets. The working stresses are 1 4 ksi for the rivets in shear and 1 8 ksi for the plates in bearing. What is the magnitude of...

Question 1 The lap foint is fastened with four 3 / 4 - in , - diameter rivets. The working stresses are 1 4 ksi for the rivets in shear and 1 8 ksi for the plates in bearing. Find the largest...

2. The lap joint is fastened by 5 one-inch diameter rivets. For P=10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing stress in the rivets, and (3.) the maximum...

This is one problem. please write clearly 2. The lap joint is fastened by 5 one-inch diameter rivets. For P=10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing...

T5 Computational Analysis (Refer the attached sheet). Problem 16. What is economical joint and where does it find applications? A double riveted double cover butt joint is used to connect plates 12...

Q-1 A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted...

21:19 L3 Statics Assignment 3... 4. Two steel plates are riveted together by means of a single lap joint as shown in Figure 3. Six rivets of diameter 9mm are used, and the load carried is 20kN. What...

10:11 I 30 75 2 3 ||| 75 30 5002 50 Figure 10 11) A wall bracket is attached to the wall by means of four identical bolts, two at A and two at B, as shown in Figure 11. Assuming that the bracket is...

Question 1 A Solid steel shaft running at 6 0 0 rpm is supported on bearings 6 0 0 mm apart. The shaft receives 4 0 kW through a 4 0 0 mm diameter pulley weighing 4 0 0 N located 3 0 0 mm to the...

Discuss the meaning of R square in regression analysis. What does an R square of 1.00 mean?

1.What mode of decay is probable for 41/18 Ar ? What mode ofdecay is probable for ? a.electron capture b. beta emissionC.positron emission D.alpha emission 2. The standard cell potential, E cell ,...

There are 108 litres of water in a tank. 9 litres flow out of the tank every hour. a How much water is in the tank after i 1 hour ii 3 hours iii 7 hours? b How long will it be until the tank is...

Which sequence correctly summarizes the accounting process? OA. Journalize transactions, prepare a trial balance, post to the accounts. B. Journalize transactions, post to the accounts, prepare a...