Question: Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts ( n 4) at

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts (n 4) at six different points in time. The operator measured the outside diameter of each sampled part and listed the results in the table below. The desired tolerance for this part is 7.250 inches + or - .009 inches.

Sample data collected by the operator of a lathe

What is the number found in the numerator of the Cp Index?

What is the number found in the denominator of the Cp Index?

What is the value of the Cp Index?

1 7.252 7.254 7.249 7.242 Total Samples Taken 2 3 4 5 7.254 7.249 7.252 7.251 7.250 7.247 7.254 7.244 7.251 7.242 7.253 7.244 7.257 7.240 7.242 7.241 6 7.260 7.266 7.245 7.235 Ave. 7.249 7.253 7.245 7.250 7.245 7.252

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts (n - 4) at six different points in time. The operator measured the outside diameter...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts (n - 4) at six different points in time. The operator measured the outside diameter...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts (n - 4) at six different points in time. The operator measured the outside diameter...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts (n- 4) at six different points in time.The operator measured the outside diameter of...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts ( n 4) at six different points in time. The operator measured the outside diameter of...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts ( n 4) at six different points in time. The operator measured the outside diameter of...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts ( n 4) at six different points in time. The operator measured the outside diameter of...

Q:

Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts ( n 4) at six different points in time. The operator measured the outside diameter of...

Q:

Problem 1 (25 Points) :- Sample data collected by the operator of a lathe process is shown below. The operator took a sample of four parts at five different points in time. The operate measured the...

Q:

Fill in the boxes on the Answer Sheet Provided. Each box should contain a number or letter reflecting your answer. Do not show any work. When you are finished, submit only your Answer Sheet attached...

Q:

A ball of radius R is rotatably mounted on an arm of the bar DOE bent at right angle at point O. The other part of this bar is vertical and rotatably mounted in a stationary ball of the same radius....

Q:

In preparing the accounts of your company you are faced with a number of problems. These are: a) The long-term future success of the company is extremely uncertain. b) At the year-end, an amount is...

Q:

Zuestion 9 of 1 0 . A millary taxpayer might want to consider making contributions to the millary Thrift Savings Plan while deployed to a combat zone because nontasable combat pay is: A good source...

Q:

When older adults have difficulty with transportation and communication, or may be reluctant to request needed assistance to which they are entitled, they may be in need of: Group of answer choices...