Question: a) In a tensile test on a metal specimen, true strain = 0.08 at a stress 265 MPa. When the flow stress = 325

a) In a tensile test on a metal specimen, true strain =

a) In a tensile test on a metal specimen, true strain = 0.08 at a stress 265 MPa. When the flow stress = 325 MPa, the true strain = 0.27. Determine the flow curve parameters n and K? b) Discuss some of the factors that affect the fluidity of a molten metal during pouring into a mold cavity?

Step by Step Solution

★★★★★

3.51 Rating (154 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a Determine the Flow Curve Parameters n and K The flow curve for a material is given by the equation ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

a) In a tensile test on a metal specimen, true strain = 0.08 at a stress = 265 MPa. When the flow stress = 325 MPa, the true strain = 0.27. Determine the flow curve parameters n and K? b) Discuss...

The following are typical tasks performed by GAS. For each task, provide an example of how GAS could be used to accomplish that task. a. Analyze a file b. Select transactions based on logical...

Discuss some of the factors that are important in determining frequency levels. Give examples of each factor.

? ? Comprehensive Problem Cost Volume Profit Analysis Based in Italy, Datura, Ltd., is an international importer-exporter of pottery with distribution centers in the United States, Europe, and...

b) Two sisters, Mary and Jane, jointly purchased an apartment using their own savings. The apartment was rented out, but because the rental rate was considered too low, they decided to sell the...

Question 4 ( a ) Show that the tensile strength of a material can be expressed as k n n ( e x p ) - n , given = n at the tensile strength, and k and n are the strength coefficient and the strain...

1. How does Kant state his basic moral principle? 2. What is the difference between how one would reason about whether it is prudent to make a false or lying promise and how one should determine...

"A metal alloy has been tested in a tensile test with the following results for the flow curve parameters: coefficient of resistance 612.4 MPa and strain hardening exponent - 0.27. The metal is now...

NOTE: Clearly show your procedure and all calculations. Enclose final answers with corresponding units in a box. During the tensile test of a metal, it was observed that when the true stress is 2 9 ,...

MET221 Manufacturing Processes Week 1 Review Assignment Problem 1. Chapter 10 Pouring Calculations A mold sprue is 25 cm long, and the cross-sectional area at its base is 3.0 cm2. The sprue feeds a...

Freshaire, Inc., produces two types of air fresheners: Mint Freshener and Lemon Freshener. Both produces are sold in 32-ounce bottles. Mint sell for $3.00 per bottle, and Lemon sells for $ 3.50 per...

Assume both parties sign the contract and it reads 15 tires at $70 each. Is the contract enforceable under the statute? If so, to what extent is it enforceable?

south of the equator at t minules after the start of the total ecliose. What is the latiose closest to the equator, in degrees, al which the lotal eclipse will be vestible? The lattude closest to the...

A system has a damping ratio of 0.15, a natural frequency of 20 rad/s, and a dc gain of 1. Use inverse Laplace transforms to find an analytic expression of the response of the system to a unit-step...

The CSV (or comma-separated values) format is commonly used for tabular data. Each table row is a line, with columns separated by commas. Items may be enclosed in quotation marks, and they must be if...

Figure P5.42 Shows the block diagram of an Automatic Voltage Regulator (Gozde, 2011). Assume in this diagram the following parameter values: K a = 10, T a = 0.1,K e = 1, T e = 0.4, K g = 1, T g = 1,...

Geiberger AG manufactures drones. On December 31, 2021, it leased to Althaus SA a drone that had cost 120,000 to manufacture. The lease agreement covers the 5-year useful life of the drone and...

Consider a structured security of the following type: The purchaser invests $1,000 and in three years gets back the initial investment plus 95% of the increase in a market index whose current price...

Samuel Bankman-Fried and FTX - reflect upon the issues of CEO liability regarding the case. Directions Samuel Bankman-Fried marketed himself as a proponent of "effective altruism," using his wealth...

A tensile test is performed on a metal specimen, and it is found that a true plastic strain of 0.20 is produced when a true stress of 575 MPa (83,500 psi) is applied; for the same metal, the value of...

A tensile test is performed on a metal specimen, and it is found that a true plastic strain of 0.20 is produced when a true stress of 575MPa (83,500psi) is applied; for the same metal, the value of K...

a. Discuss the importance of what you see in Column 2 of the table. b. Draw using box plots the tensile strength versus polyester weight percentage. Discuss. c. Help Mr. Tee to make some...

2. In addition to the request in 1. above, Mr. Tee the Quality Manager also provided you with some information and data of the experiments done to develop a new textile product (see the table below)....

Please need help immediately for this matlab problem. CSM ENGR 215 Lab 6 Due: 10/2618 11:59PM CSM ENGR 215 Lab 6 Duc: 102618 11:59PM Problem 2: Tensile Test Data Analysis (Lab 5 Problem 3 Continued)...

4. Part 1: Tensile testing The aim of the tensile test is to find the yield and ultimate tensile strengths and corresponding normal strains of the test material. This enables the prediction of the...