Question: Technician A says that when performing a voltage drop, the DMM should be set on the ohms setting. Technician B says that when performing a

Technician A says that when performing a voltage drop, the DMM should be set on the ohms setting. Technician B says that when performing a voltage drop the DVOM should be set to the voltage setting. Who is correct

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Physics Questions!

1. Refer to Figure 3-28 below. Technician A says that the compressor clutch diode in the clutch electrical circuit is in series with the compressor clutch coil. Technician B says that a blown HVAC 20...

Technician A says when doing a voltage drop test, the voltmeter needs to be set to ohm. Technician B says current has to be flowing to do a voltage drop test. Who is correct

O D. squareness Question 32 Question 30 1 pts 32. Technician A says that the thermostat controls maxi- mum engine temperature. Technician B says if the en- gine continuously runs hot, install a...

First choose correct option and explain step by step by with reason 1A) Guide replacement is being discussed. Technician A says to match guide materials to valve stem materials when selecting valve...

22. While conducting a cylinder leakage test, bubbles 24. Technician A says that excessive grinding of valve are seen in the coolant in the radiator. Technician A faces and seats allows the valve...

Technician A says that fluorescent light bulbs may be hazardous waste. Technician B says that used spraybooth filters may be hazardous waste. Who is right? A only B only Both A and B Neither Anor B...

Technician A says that a conditionally-exempt small quantity generator is required to use hazardous waste shipment manifests. Technician B says that maintaining hazardous waste records may be...

1.Technician A says that MAP sensor equipped engines are the most accurate way to control the A/F ratio. Technician B says that MAF sensor equipped engines have the most accurate way to control the...

30. Most sealed bearings used on the front wheels of front-wheel-drive vehicles are uSually which type? a. Roller bearing b. Single tapered roller bearing c. Double row ball bearing d. Needle roller...

Keruing Sejahtera Bhd (KERUING) is a company dealing with health food products operating in Bukit Kayu Hitam, Kedah. The partial statement of the financial position of KERUING as at 31 December 2020...

Hank Greenberg was the formidable CEO of AIG, the largest insurer in the United States. Mr. Greenberg was removed from his position when the SEC raised issues regarding the companys accounting...

Use the Chain Rule t o find d w d t . w = 5 x 3 y 6 z , x = 9 t , y = c o s ( 4 t ) , z = t s i n t

A particle is scattered by a potential at sufficiently low energy so that the phase shifts & =() for 1>1. Assume rotational symmetry. (a) Show that the differential scattering cross section has the...

Q: What is horizontal line test? Q2: write down application of homogenous differential equations

Find the physical dimensions of wave function (r) of a particle moving in three dimensional spaces.

Question 7 . Given the following simple maze, convert the maze into a graph. ( 5 points ) Question 8 . Implement depth first search in the maze function in homework 1 . py . ( 2 0 points ) Question 9...

13. Try to imagine how you would feel if you had tackled the problem, the con-flict, the challenge, etc., that made you powerless in task 12, for example upstairs, confident, confident, calm,...

15. Ask yourself the following questions: What do you want to remember from your everyday experiences? These are the experiences that fill most of your life. They may take 9099% of your time. What do...

What reward will you give yourself when you achieve this?