Question: The bracket shown supports a load P = 10.5 kN. The allowable stress is 174 MN/m in tension and 122 MN/m in compression. Determine

The bracket shown supports a load P = 10.5 kN. The allowable

The bracket shown supports a load P = 10.5 kN. The allowable stress is 174 MN/m in tension and 122 MN/m in compression. Determine the required cross-sectional areas of members AB and BC. Express your answers in mm. 50 cm -80 cm- B

Step by Step Solution

★★★★★

3.44 Rating (157 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The bracket shown in the figure supports a load P 105 kN and the allowable stress is 174 MNm in tension and 122 MNm in compression asy pair A B C D O ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Accounting Questions!

The weight and radius of friction disk A are WA = 12 lb and rA = 6 in.; the weight and radius of friction disk B are WB = 6 lb and rB = 4 in. The disks are at rest when a couple M of moment 7.5 lb ??...

An L-shaped bracket lying in a horizontal plane supports a load P = 150 lb (see figure). The bracket has a hollow rectangular cross section with thickness t = 0.125 in. and outer dimensions b = 2.0...

The bracket shown supports a force P. Assume that both members have their ends pinned in the plane of the bracket ABC and fixed in a perpendicular plane. The modulus E = 207 x 10 kN/m, and the yield...

Figure P312 shows a small truss spanning between solid supports and suspending a 10.5 kN load. The cross sections for the three main types of truss members are shown. Compute the stresses in all of...

A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L = 150 mm, spacing a = 50 mm): two of steel and one of aluminum. The wires also support a load P acting on the...

Four masses are positioned in the xy-plane as follows: 300 g at (x = 0, y = 2.0 m), 500 g at (2 0 m, 3.0 m), 700 g at (50 cm, 30 cm), and 900 g at (80 cm, 150 cm). Find their center of mass.

10.14 A four-stage boiler feed pump has suction and discharge lines of 10 cm and 7.5 cm inside diameter. At 3500 rpm, the pump is rated at 0 025 m3 s against a head of 125mwhile handling water at 115...

A crane of mass 3 000 kg supports a load of 10 000 kg as in Figure P12.47, the crane is pivoted with a frictionless pin at A and rests against a smooth support at B. Find the reaction forces at A and...

The steel plane truss shown in the figure is loaded by three forces P, each of which is 490 kN. The truss members each have a cross-sectional area of 3900 mm2 and are connected by pins each with a...

A steel column of hollow circular cross section is supported on a circular steel base plate and a concrete pedestal (see figure). The column has outside diameter d = 250 mm and supports a load P =...

Hollis Corporation has the following budgeted schedule for expected cash receipts and cash disbursement. Hollis begins July with a cash balance of $20,000, $15,000 of short-term debt, and no...

a. Using the characteristics of Fig. 3.14a, determine ac at IB = 80 it A and VCE = 5 V. b. Repeat part (a) at IB = 5 A and VCE = 15 V. c. Repeat part (a) at IB = 30 A and VCE = 10 V. d. Reviewing the...

As of December 31, 20X1, Mantua Company has the following three loans payable scheduled to be repaid in February 20X2. Loan A: Loan A is for $10,000. Mantua intends to repay Loan A when it comes due...

The uniform bar of mass M and length l has a small roller of mass m with negligible bearing friction at each end. Determine the period ???? of the system for small oscillations on the curved track....

Run a frequency count on variable X 3 Competent Employees. Do the customers perceive employees to be competent?

A 25-L tank, shown in Fig. P4.136, that is initially evacuated is connected by a valve to an air supply line flowing air at 20C, 800 kPa. The valve is opened, and air flows into the tank until the...

An electromagnet a. uses an electric current to produce a magnetic field b. uses a magnetic field to produce an electric current c. is a magnet that has an electric charge d. operates only on...

Claudia James took out a $200,000 life insurance policy on her husband and named herself as beneficiary. Three months later they were divorced, and a month after that her ex-husband died in a car...

Critical values of t are no longer used in hypothesis testing act as markers cutting off rejection regions are always one-tailed are always two-tailed

175 mm Load on bracket Simple supports 275 mm A Bracket A 450 mm 12 mm W Section A-A A part of a bracket in the seat assembly of a bus is shown in the above picture. The load varies from 1450N to...

8. A part of a bracket in the seat assembly of a bus is shown in Figure P5-8. The load varies from 1450 to 140 N as passengers enter and exit the bus. mm Load on bracket Simple supports 275 mm A...

Consider the printed circuit board (PCB) mounted on a cantilevered aluminum bracket shown in Fig. 4.23(a). Design the bracket to withstand an acceleration level of $100 \mathrm{~g}$ under the...

Q3. The bracket shown in figure supports a 48 kN load. The fillet weld extends for the full 120 mm length on both sides. What weld size is required to give a safety factor of 4 if E60 series welding...

The bracket shown in Figure P11.14 supports a 4000 N load. The fillet weld extends for the full 120 mm length on both sides. What weld size is required to give a safety factor of 3 if E60 series...

A swivel C bracket shown in Figure P11-24 is mounted to a ceiling of a building and has a speaker (not shown) of 30 lbf hanging from each mounting hole. The mounting bracket is made of A 36 steel...