Question: The distributed load on the beam shown is 2 . 5 k N m . What is the maximum shear stress in the beam at

The distributed load on the beam shown is 2.5kNm. What is the maximum shear stress in the beam at the interface between the two members (at 150 mm from the bottom). If nails are used to connect the members and the nails have an allowable shear strength of 2 kN , what is the maximum spacing of the nails at the point of maximum shear?
The distributed load on the beam shown is 2 . 5 k

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Q.4 A simply supported U beam is loaded as shown in Figure Q.4(a). Its cross section is shown in Figure Q.4(b). w kN/m 8 m Figure Q.4(a) X yc XX 25 y 250 y ** 25 Figure Q.4(b) (All dimensions are in...

Q:

(c) Calculate the moment of inertia, I of the beam. (4 marks) (d) Calculate the maximum tensile bending stress and maximum compressive bending stress. Indicate the location of these two maximum...

Q:

A solid cylindrical shaft with a diameter of 9 0 mm is subjected to a bending moment of 1 0 0 0 Nm and a torque of 8 0 0 Nm . Calculate the principal stresses, maximum shear stress, and von Mises...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

Q:

Predict the nucleate-boiling heat transfer coefficient for water boiling at atmospheric pressure on the outside surface of a 1.5 cm OD vertical copper tube 1.5 m long. Assume the tube-surface...

Q:

1. Which of the following is not a common cost flow assumption used in costing inventory? a. First-in, first-out b. Middle-in, first-out c. Last-in, first-out d. Average cost 2. The control principle...

Q:

Explain why the following input data also needs to be verified: >>Entering a telephone number >> Entering a pupil's name >> Entering a part number in the form XXX999, when X must be a letter and 9...

Q:

10. On February 1, 2024, Sanyal Motor Products issued 9% bonds, dated February 1, with a face amount of $80 million. The bonds mature on January 31, 2028 (four years). The market yield for bonds of...