Question: The gear motor can develop 2 . 2 4 kW when it is rotating at I 5 0 revolutions per minute. The maximum torsional shear

The gear motor can develop 2.24 kW when it is rotating at I 50 revolutions per minute.
The maximum torsional shear stress in the shaft is 83 MPa .
Calculate the minimum diameter of the shaft that can be used.
The gear motor can develop 2 . 2 4 kW when it is

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

The Gearbox shown in Figure is connected to a Motor M rotating at 3200 rpm. The system is used to transmit power to two mechanical loads: Load 1 requiring (10-0.6*(L+S)) kW connected to the output...

Q:

Soalan 1 KIG 1 0 1 4 Question 1 a ) Dua aci yang padu dan gear seperti yang ditunjukkan dalam Rajah 1 telah digunakan untuk menghantar 1 2 k W dari motor pada titik A yang beroperasi pada kelajuan 1...

Q:

Question 1 A circular cross - section shaft is mated to a motor rotating at 1 5 0 0 rpm . The shaft is made 4 0 C 8 steel and is used to transmit power to two pulleys of diameter 3 0 0 mm and 2 0 0...

Q:

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

Q:

A punch press is used to create 3 5 holes per minute in a plate, and each hole - piercing operation requires 1 1 kN - m of energy during a single revolution. Furthermore, each piercing operation...

Q:

Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. What is the torque magnitude, T B , acting on gear B ? please solve all 1 0 parts seen in the...

Q:

QUESTION 4 : a ) Define and draw diagrams of the concept of Torque on a cylindrical bar, showing Torque ( T ) and angle of Twist ( theta ) . b ) A compound steel [ G = 8 0 GPa ] shaft consists of...

Q:

Question 1 A 100 mm diameter shaft with a length of 6 m is connected by a flange coupling and transmitting maximum power. A square key of 20 mm is used to connect the shaft and the hub. The coupling...

Q:

The following information is from the December 31, 2017 balance sheet of Tudor Corporation. Preferred Stock, $100 par $370,000 Paid-In Capital in Excess of Par - Preferred 31,000 Common Stock, $1 par...

Q:

XYZ had a bank statement balance of $300 at Jan 31. The following were noted: a) Outstanding cheques not yet cashed from January were $30. b) An error was made by the company in that a payment was...

Q:

Roybus, Inc., a manufacturer of flash memory, just reported that its main production facility in Taiwan was destroyed in a fre. Although the plant was fully insured, the loss of production will...

Q:

. Zuka Led, manufactures a single product whose cost structure is as given below : Sh Sh Direct Materials Material ABACake @ 25 per kg) 50 Material, BCA(3 Litres @ 15 perlitre) 225 275 Direct...