Question: The upper and lower customer specified limits for a component are 6.40 and 5.20 inches respectively. The process standard deviation is 0.15, and the process

The upper and lower customer specified limits for a component are 6.40 and 5.20 inches respectively. The process standard deviation is 0.15, and the process average is 5.70 inches. Calculate Process Capability Index (Cpk)

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

SOLUTION To calculate the Process Capability Index Cpk you need to use the following formula Cpk min... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related General Management Questions!

Exercise 1 stiffness matrix of a simple frame. Find the stiffness matrix for the problem on the right: Consider: E = 200 GPa A = 0.2 cm /=1m y EA 2EA 1 X 31 F,u 42

The steel beam shown below carries a uniform distributed load and a concentrated load at its free end. The elastic modulus, E=29000 ksi, and the second moment of area, I=1600 in, are constant along...

1. The process capability measures Cp and Cpk differ because A) Only one ensures the process mean is centered within the limits B) Cp values above 1 indicate a capable process; Cpk values above 2...

The upper and lower customer specified limits for a component are 6.40 and 5.20 inches respectively. The process standard deviation is 0.15, and the process average is 5.70 inches. The Process...

The upper and lower customer specified limits for a component are 6 . 4 0 and 5 . 2 0 inches, respectively. The process standard deviation is 0 . 1 5 , and the process average is 5 . 7 0 inches. What...

The upper and lower customer specified limits for a component are 6 . 4 0 and 5 . 2 0 inches respectively. The process standard deviation is 0 . 1 5 , and the process average is 5 . 7 0 inches. The...

Question 1 9 5 pts The upper and lower customer specified limits for a component are 6 : 4 0 and 5 . 2 0 inches respectively. The process standard deviation is 0 . 1 5 , and the process average is 5...

The upper and lower customer specified limits for a component are 6 . 4 0 and 5 . 2 0 inches respectively. The process standard deviation is 0 . 2 0 , and the process average is 5 . 7 0 inches. The...

Soda and lime are added to a glass batch in the form of soda ash (Na2CO3) and limestone (CaCO3). During heating, these two ingredients decompose to give off carbon dioxide (CO2), the resulting...

Demonstrate that the wave functions of the stationary states of a particle confined in a unidimensional potential well with infinitely high walls are orthogonal, i.e. they satisfy the condition Here...

Use the Intermediate Value Theorem ( If applicable ) to justify why the equation 5 x x 2 - 6 - 1 must have at least one solution between x = 0 and x = 4 If the IVT cannot be applied, explain why ( i...

In a free space wireless propagation environment, transmit power between a transmitter and receiver usually decreases due to free space path loss denoted as L subscript f space(dB) and can be...

1. why did bribery became so pervasive at Siemens? 2. Based on your knowledge of descriptive ethical theories, propose a specific plan of improving the bribery situation at siemens? 3. what are the...

Smooth steel (SG =7.86) sphere is immersed in a stream of ethanol at 20C moving at 1.5 m/s. Estimate its drag inN from Fig. 5.3a. What stream velocity would quadruple itsdrag? Take D =2.5 cm. 5 4...

You have the following information A B Total Rent 2400 4800 2000 2000 800 12000 800 2000 500 4000 Electricity Indirect Labor 400 300 1200 2000 1000O 800 1000 6000 2500 1600 200 500 200 5000...

If X~b(18,),then find: a. the m.g.f., u and o2. b. p(x 0).

Which management tool produces a "snapshot" of all the identified risks at a given point in time? Cause and effect analysis Baseline identification and analysis Risk management planO, Cost/benefit...

Ace Jet Airlines is losing business because of late flight departures. A quality improvement team has met to discuss the issue. They have decided to construct a fishbone diagram to try and identify...

SunTech Co. is developing a new window film that will prevent windows from shattering upon impact. The specifications on the film thickness are 370 10 m (micrometers). The film is made up of three...

Two machined parts must be assembled as shown in the diagram below. To function properly a clearance must be maintained between the two parts. The critical dimension on Part A has specifications of...

What information does a decision maker need in order to perform an expected-value analysis of a problem? What options are available to the decision maker if the probabilities of the states of nature...

Under what circumstances is expected monetary value appropriate as a decision criterion? When isnt it appropriate?

Explain the term suboptimization.