Question: To control a device using the circuit shown. it should be that Vab=8V. Select the resistors when it is required that all resistors be greater

To control a device using the circuit shown. it should be

To control a device using the circuit shown. it should be that Vab=8V. Select the resistors when it is required that all resistors be greater than 1 and R3+R4=20. 1. what should be the value of rl,r2,r3, and r4,s0 that when simulated IN TENKERCAD the output voltage in the multimeter is right 2. translate the circuit into a breadboard use breadboard small To control a device using the circuit shown. it should be that Vab=8V. Select the resistors when it is required that all resistors be greater than 1 and R3+R4=20. 1. what should be the value of rl,r2,r3, and r4,s0 that when simulated IN TENKERCAD the output voltage in the multimeter is right 2. translate the circuit into a breadboard use breadboard small

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

1 Figure 6.1: Gate implementation of F Identify the logic levels required at the input and those produced at the output. Review the use of PULL-UP/DOWN resistors to get the correct logic levels at...

The rate at which the capacitor in a series RC circuit charges or discharges depends on the capacitance C of the capacitor and resistance R in the circuit. We define a time constant, T, as the time...

Remote Lab 6 - RC CIRCUITS is and ni i sonofalem ban jollapans Learning Goals: goldsuzie gnigysdozib to gnigisdo and) Tertia al sulev Isilini all 10 RVE of gob of Jivanjo After completing this...

Please answer the following in detail given the lab report and data shown below: 1. Resistance, R, is defined using R = V/I where V is the voltage across a resistor, and I is the current. R is...

Please Help me with the following all information there choose the direction for each letter AP Transaction Entry - Accounting Pc X Homework Help - Q&A from Onl X A Chapters 18 and 19 - PHY1620, S X...

i need al the work and lab simulations and pre labs and calculations. LAB SIMULATIONS MUST BE ON PROTEUS ISIS INTRODUCTION: Linear circuit elements resistors, capacitors, and inductors are the...

E-Tutorial Physics Book Note: I have attached below the lesson for the two (2) activities. Thank you. Activity 1. Directions: Look at each circuit below and show the solution using Kirchhoff's Rules...

1: A defibrillator sends a 7.5 A current through the chest of a patient by applying a 12000 V voltage as in the figure. What is the resistance of the path in k? 2: During open-heart surgery, a...

Extend your design from Part V code below so that is uses all 7-segment displays on your DE-series board. Your circuit needs to display a three- or four-letter word, corresponding to Table 2, using...

CECS 346 Project 3 A Smart Home By Dr. Min He Preparation: You will need two LaunchPads, 3 stepper motors with drivers (can be checked out from the instructor), 2 obstacle avoidance sensors (can be...

One thousand minis are recorded from a mammalian NMJ, and the average amplitude is 0.5 mV. At the NMJ of an adjacent fiber, a similar recording gives an average of 1.0 mV. What is the most likely...

Below is the textabbr.txt file contents: r:are u:you ttyl:talk to you later l8:late brb:be right back lol:laughing out loud bbl:be back later tldr:too long; didn't read rofl:rolling on floor laughing...

c. Average collection period: Credit sales are 60% of total sales 113,400.00. accounts receivable closing balance is 7300

(Rp) criterion, it will fail to meet (d) For a decentralized controller with pairing with one negative (e) A digital controller containing one negative stable fortion than its counterpart wiedinski...

What is the purpose of a Position Control Table? What relationships to other Compensation Tables would be important?

What Data Elements are usually found in the Job Family Table, and what is the relationship of the Job Family Table to the Occupation Table?

What is the relationship between the Internal Staff Compensation Target Table and the Internal Staff Compensation Data Table?