Use the chart example provided above to answer those in excel. All sections are needed. Two failure mode is needed for every function. Thanks

This template lustraces a Failure Mode and Pico TOWN Effects Analysis (FMEA), also referred to as a instructions for data antru About Quality web site. Initiate action to reduce the RPN Potential Failure Mode and Effects Analysis (PFMEA) or Failure Modes, Effects and Re-evaluate the RPN value after Leam About FMEA completion of the recommended Learn About Quality FAILURE MODE AND EFFECTS ANALYSIS Item: Drill Hole Responsibility: J. Doe FMEA number: 123456 Model: Current Prepared by: J. Doe Page : 1 of 1 Core Team: J. Doe (Engineering), J. Smith (Production), B. Jones (Quality) FMEA Date (Orig): 171/2008 Rev: 1 CPotential Current Potential Potentials Cause(s) Action Results Process Process Responsibility and Failure Effect(s) of Mechanisc Controls t Recommended Function SOD R Target Completion Mode Failure vs m(s) of u Prevention Action(s) . N Date Actions Taken C. Failure r Detection C volt N Break Hole too through Improper Drill Blind Hole 7 machine 3 Operator training 63 0 deep bottom of and instructions plate Hole not Improper Incomplete deep Operator training 3 machine thread form 0 3 45 enough and instructions set up Broken Install Tool 5 5 None 9 225 Drill J. Doe 3/1/2008 55125 Detectors 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 set up 5 0 1111111 1 HW 3 asks you to perform a FMEA analysis for a Whirlpool French door refrigerator. A FMEA template and the product manual is attached. Use the information from the manual to familiarize yourself with the sub system, and use your sub- matter knowledge to analyze the failure modes. The trouble shoot suggestions in the manual help you understand how each sub system works. For engineering numbers you don't know exactly, you can do so by your engineering knowledge and infer them based on info from the manual. Required FMEA analysis: 1. Perform FMEA analysis on the following subsystems: a). Cooling system b). Software and Control system 3). water and ice dispensing system d). Refrigerator case, sealing, and storage 2. For each sub-system, identify at least two failure modes. Give a total of at least 10 failure modes. 3. You are asked to make suggestions on failure detection or failure prevention/improvement as you see approximate and redo the RPN number. This template lustraces a Failure Mode and Pico TOWN Effects Analysis (FMEA), also referred to as a instructions for data antru About Quality web site. Initiate action to reduce the RPN Potential Failure Mode and Effects Analysis (PFMEA) or Failure Modes, Effects and Re-evaluate the RPN value after Leam About FMEA completion of the recommended Learn About Quality FAILURE MODE AND EFFECTS ANALYSIS Item: Drill Hole Responsibility: J. Doe FMEA number: 123456 Model: Current Prepared by: J. Doe Page : 1 of 1 Core Team: J. Doe (Engineering), J. Smith (Production), B. Jones (Quality) FMEA Date (Orig): 171/2008 Rev: 1 CPotential Current Potential Potentials Cause(s) Action Results Process Process Responsibility and Failure Effect(s) of Mechanisc Controls t Recommended Function SOD R Target Completion Mode Failure vs m(s) of u Prevention Action(s) . N Date Actions Taken C. Failure r Detection C volt N Break Hole too through Improper Drill Blind Hole 7 machine 3 Operator training 63 0 deep bottom of and instructions plate Hole not Improper Incomplete deep Operator training 3 machine thread form 0 3 45 enough and instructions set up Broken Install Tool 5 5 None 9 225 Drill J. Doe 3/1/2008 55125 Detectors 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 set up 5 0 1111111 1 HW 3 asks you to perform a FMEA analysis for a Whirlpool French door refrigerator. A FMEA template and the product manual is attached. Use the information from the manual to familiarize yourself with the sub system, and use your sub- matter knowledge to analyze the failure modes. The trouble shoot suggestions in the manual help you understand how each sub system works. For engineering numbers you don't know exactly, you can do so by your engineering knowledge and infer them based on info from the manual. Required FMEA analysis: 1. Perform FMEA analysis on the following subsystems: a). Cooling system b). Software and Control system 3). water and ice dispensing system d). Refrigerator case, sealing, and storage 2. For each sub-system, identify at least two failure modes. Give a total of at least 10 failure modes. 3. You are asked to make suggestions on failure detection or failure prevention/improvement as you see approximate and redo the RPN number