Question: Use Timer 3 in CTC l mode to generate a square wave of period 0 . 5 seconds at Port B Pin 6 , while

Use Timer 3 in CTC l mode to generate a square wave of period 0.5 seconds at Port B Pin6,
while at the same time, monitor Port C Pin 6. If it is HIGH, Clear port D to ZERO, otherwise
continue monitoring. Write the program in Assembly Language. (Hint: Interrupt)

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

Q:

Use Timer 3 in CTC 1 mode to generate a square wave of period 0 . 5 seconds at Port B Pin 6 , while at the same time, monitor Port C Pin 6 . If it is HIGH, Clear port D to ZERO, otherwise continue...

Q:

Use Timer 3 in normal mode to generate a square wave of period 0 . 5 seconds at Port B Pin 6 , while at the same time, monitor Port C Pin 6 . If it is HIGH, Clear port D to ZERO, otherwise continue...

Q:

microcontroller 8051 (MPC82G516A) to finish square wave generation. (timer) question fig. microcontroller 8051 (MPC82G516A) to finish square wave generation. some code picture number is 10626140...

Q:

1 . Assuming XTAL = 1 6 MHz , show a program to generate a 0 . 2 5 seconds time delay. Use any timer you want. 2 . With XTAL = 2 2 MHz , find the delay obtained using the following program DELAY: MOV...

Q:

solve the quastion with red circule (34,37,38) 11.0592 MHz 21. Assume that XTAL - 16 MHz Find the THI.TLI value to generate a time delay of 5 ms. Timer I is programmed in mode I 22. Assuming that...

Q:

10.2 Write programs in PIC18F assembly and C: (a) (b) (c) (d) (e) To initialize Timer as an 8-bit timer to provide a time delay with a count of 100. Assume a 4 MHz internal clock with a prescaler...

Q:

Assuming XTAL = 4MHz, Which are the values you have to write to TCNT0 and TCCR0 if you want to generate a square wave of 62.5Hz frequency on pin 3 of Port B? Use Timer0. Normal mode, with pre scalar...

Q:

Questions Write a program that adds the three numbers stored in data registers at 0 2 0 , 0 3 0 , and 0 4 0 and places the sum in data register at 0 5 0 . Write a program to add two 2 4 - bit numbers...

Q:

Counters and PWM Draw neat diagrams in response to these questions. Many of the answers to these questions are available in the datasheet. For the purpose of this assignment, refer to the datasheet...

Q:

Assume that XTAL = 1MHz. Find the OCRO value in decimal) needed to generate a time delay of 0.2 ms. Use CTC mode, no prescaler mode Assuming that XTAL = 8 MHz with prescaler of 1024, and we are...

Q:

Explain why Monetarists believe the Fed should have expanded the money supply during the Great Depression?

Q:

Presented below is the December 31 trial balance of New York Boutique. Instructions(a) Construct T-accounts and enter the balances shown.(b) Prepare adjusting journal entries for the following and...

Q:

Copy your R Code and plots to the answers. Select 5 stocks from BIST 3 0 Index and 5 stocks from BIST 1 0 0 and dounload the price data for the period from beginning of 2 0 2 2 to end of 2 0 2 3 and...

Q:

Riku is a project manager who has 1 5 employees reporting directly to him. Those 1 5 employees represent Riku's a . chain of command. b . unity of direction. c . unity of command. d . span of control.

Q:

d. Describe any challenges in trying to communicate. If there were no challenges, explain why you think it was so easy.

Q:

f. Did they change their names? For what reasons?

Q:

2. Describe three approaches to the study of intercultural communication.