Question: Using the Conjugate beam method, determine the slope at point B and C and the deflection at point C of the beams shown in figure

Using the Conjugate beam method, determine the slope at point B and C and the deflection at point C of the beams shown in figure below, Take E=200GPa and I=800106mm4.
200kN
Using the Conjugate beam method, determine the

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

The beam shown below is pin supported and A and roller supported at B. Young's modulus, E, and moment of inertia, I, are constant over the beam. 1) Draw shear and moment diagrams, then sketch the...

Q:

2. The beam in the figure is made of material having modulus of elasticity E = 200 GPa . The moment of inertia of segments AB and CD of the beam is I = 6.77 10-6 m, while the moment of inertia of...

Q:

can someone help me with this sample lab report? I didn't do so well with a similar one in the semester. what I'm most confused about is number 5 and 7. Bending Lab guidelines: 1. Follow the handout...

Q:

Determine the slope and the displacement at midspan of the non-prismatic beam as shown in figure below. E = 200 GPa, I = 100 x 106 mm4. Use conjugate beam method. Use a) DIM b) MAM (deflection only)...

Q:

Figure Q3 shows a propped cantilever beam ABCD with a roller support at A, carrying a point load at B and subjected to a uniformly distributed loading from point B to C. Given EI = 2250 kNm, by using...

Q:

Consider a built-in beam ABCDE with a total length of 5 meters, as shown in Figure Q1. The beam is subjected to a uniform distributed load along the length BD, and a concentrated load of 30 kN...

Q:

Figure Q 3 shows a propped cantilever beam ABCD with a roller support at A , carrying a point load at B and subjected to a uniformly distributed loading from point B to C . Given E I = 2 2 5 0 k N m...

Q:

The cantilever beam shown below has an applied moment of M = 19.0 kipin at point B and a distributed load of w 0 = 8.0 kip/in centered at point C . The beam is fixed to a wall at point A , has a...

Q:

Solve using Matlab Single equations So far I have: L= 10*12; E= 30*10^6; I= 5; F=15000; a=4*12; b=L-a; x=sqrt((L^2-b^2)/3) ymax=((F.*b.*x)/(6.*E.*I.*L)).*(L.^2-x.^2-b.^2) ymax_v=0.75*ymax >>results x...

Q:

Note - Use Conjugate beam method. Thanks Please solve these Deflections problems using A. Conjugate beam method 2. Determine the slope at point of the beam in the figure. E = 200 GPa, I = 6(106) mm....

Q:

Determine the dimension of the vector space spanned by x = [1 2 2 1], x = [1 0 0 1], X3 = [3 4 4 3].

Q:

The same disability insurance policy offers four alternative premium payment plans: an annual premium of $666.96, semiannual premiums of $341.32, quarterly premiums of $173.62, or monthly premiums of...

Q:

Once the depreciation expense for a long - lived asset is calculated: Multiple Choice it cannot be changed because of the cost principle. it may be revised based on new information. any changes are...

Q:

Go to https://www.sec.gov/ read the notes to facebooks most recent 10Q and or 10K report. Is there any mention of a contingent liability for an FTC fine? Based on this article, do you think ...