Question: Using the Method of Section, determine the force in Member HC in kN . ( positive value indicates tension )

Using the Method of Section, determine the force in Member HC in kN.(positive value indicates tension)
Using the Method of Section, determine the force

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Using the method of section, determine the force in member CF . The vertical reaction at point E is given. The Problem. The Free Body Diagram of the Right Side. 8 . 7 kN ( C ) 4 k N ( T ) 3 . 2 1 kN...

Q:

Problem 5: Method of Sections d Inputs: d = 4 m A B D E F D M H 1 J K L a a 3 m (all horizontal members are this length) P = 45 kN P There is a pin at A and a roller at G. Using the method of...

Q:

full working step and explanation Figure 1 shows a truss with loads and supports. At A, it is pin connected and roller connected at E. a) Draw the free body diagram of the truss. (3 Marks] b)...

Q:

Consider the truss shown in ( Figure 1 ) . Take P 1 = 9 . 0 k and P 2 = 8 . 5 k . Assume all members are pin connected. Determine the force in member A H . Indicate if the member is in tension or...

Q:

The truss shown was designed to support the roof of a food market. Knowing that Pa7kN, Q-5kN. h1-3m, h2-3.9m, h3-1,8m, h4-5.1m, L1-3.9m, L2-2.73m, 134.29m, L4-3.9m,determine, 1) the force in member...

Q:

F 1 = 4 0 k N F 2 = 3 0 k N H C o f the truss, and state i f the member i s i n tension o r compression. Express your answer t o three significant figures and include the appropriate units. Enter...

Q:

Determine the force in member HC . Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case...

Q:

Determine the force in member H C of the truss below. Indicate as positive if the member is in tension and negative ( - ) if the member is in compression. Provide the answer in k N

Q:

By using the method of sections, determine the force in members BC, BF, CF and EF of the truss and state if these members are in tension or compression. Set P= 12 kN, P = 15 kN and P3=9 kN. (Note:...

Q:

Problem 5: Inputs: h = 2 m, x = 2 m, P1 = 0 kN, P2 = 10 kN, P3 = 5 kN, P4 = 24 kN, P5 = 9 KN There is a pin at A and a rocker at G. Using the method of sections, determine the force in members: a) EI...

Q:

Using the information given for the following three independent cases, compute the amount of pension-related asset/liability that would be reported on the balance sheet. Clearly indicate whether the...

Q:

The bank portion of the bank reconciliation for Backhaus Company at November 30, 2010, was as follows. The adjusted cash balance per bank agreed with the cash balance per books at November 30. The...

Q:

5. Write a single rotate instruction that exchanges the high and low halves of the DL register.

Q:

A customer offered to pay Larry in November 2021 for services rendered that year if Larry would pick up the check at the customer's office, located one mile away. Larry did not go to collect the...