Question: Using the moment area method, find the deflection under the P applied load. A is a pin, C is a roller. E = 2 0

Using the moment area method, find the deflection under the P applied load. A is a pin, C is a
roller.
E=200 GPa and I=216 x 106 mm4, EI constant. P =70 KN, a=2.5m, b=1mUsing the moment area method, find the deflection under the applied load. is a pin, is a
roller.
=200GPa and =2161064, El constant.
Using the moment area method, find the deflection

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Moment Area method - Theorem 1 Week 1 1 Tuterial Using the moment area method, find the slopes at supports A and C . A is a pin, C is a roller. E = 2 0 0 CPa and I = 2 1 6 1 0 6 m m , EI constant....

Q:

Using the moment area method, find the deflection and slope at the centre of the beam and find the slope at both ends of the beam. Given dimensions are in inches and distributed load has units of lb...

Q:

Using the moment area method, find the slopes at supports A and C . A is a pin, C is a roller. E = 2 0 0 GPa and I = 2 1 6 1 0 6 m m 4 , EI constant. p = 7 0 kn , a = 4 m and b = 1 m find Find the...

Q:

Test II CE 3 3 2 Structural Analysis 1 - For the beam shown in Figure P - 1 / 3 , calculate reactions and draw shear and moment diagrams. What is the maximum shear and moment? A is a pin, B & D are...

Q:

The simply - supported beam ABC is loaded as shown in Figure Q 3 . Support A is a pin, and Support C is a roller. A uniformly distributed load of 5 0 k N m is applied in the segment of both A B and B...

Q:

A cantilever beam, of length L = 3 m , carries a point load of P = 6 k N at the tip of the beam as shown in Figure Q 4 There is also a clockwise concentrated moment 2 0 k N - m applied at the tip of...

Q:

Can someone explain and show the work on how to solve this problem using the moment area method. How do you find the deflection and slopes at both the ends. This is the work I have currently but I am...

Q:

As shown in Figure 1 , the beam ABC is loaded with a uniform distributed load ( UDL ) of w in the segment of A B and B C . Support A is a pin, and Support C is a roller. The beam has a flexural...

Q:

The beam shown in Figure 4 below is pin supported at A and roller at B . A point load of 6 0 k N is applied at 6 m from A . Assume that E l as 3 0 , 0 0 0 k N m 2 and neglect the weight of the beam,...

Q:

Structures The simple frame shown in Figure 1 represents a simple one - storey building. The frame supports a uniform lateral load W . The beam has a second area of moment, I, value twice that of the...

Q:

Based upon the T accounts in Exercise 2, prepare the nine journal entries from which the postings were made. Discuss.

Q:

A filling process is supposed to fill jars with 16 ounces of grape jelly. Specifications state that each jar must contain between 15.95 ounces and 16.05 ounces. Ajar is selected from the process...

Q:

The employer portion of the payroll tax rate, including the portion dedicated to Social Security ( OASDI ) and the portion dedicated to Medicare funding, on a covered worker's earnings up to the...

Q:

XYZ Corporation owns equipment with a book value of $230,000. The equipment has a fair value less costs to sell of $195,000, expected future cash flows $210,000, and its value-in-use is $190,000....