Question: Water flows into the horizontal bend fitting at A with a velocity of V = 8 m s , and exits at B into a

Water flows into the horizontal bend fitting at A with a
velocity of V=8ms, and exits at B into a tank having
a gage pressure of 50kPa, as shown in (Figure 1).
Determine the x-component of force at C needed to hold the fitting in place.
Express your answer to three significant figures and include the appropriate units.
Part B
Determine the y-component of force at C needed to hold the fitting in place.
Express your answer to three significant figures and include the appropriate units.
Part C
Determine the moment at C needed to hold the fitting in place.
Request
THE ANGLE THAT IS CUT OFF IS 30\deg

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

Find the horizontal force of the water on the horizontal bend shown. The inside diameter of the pipe is 8.0 cm and the inside diameter of the nozzle is 4.0 cm. The inlet velocity V1 is 10 m/s. You...

Q:

Water flows through a horizontal bend and discharges into the atmosphere as shown in figure. When the pressure gage reads 69kPa, the resultant force in x-direction, FAX, that is required to hold the...

Q:

The figure below shows a liquid of Specific Gravity SG = 1.2 flowing around a vertical two- dimensional bend with circular streamlines. Along the vertical plane passing through points (1) and (2),...

Q:

Water ( = 1000 kg/m 3 ) flows through a horizontal bend and T section as shown. At section a the flow enters with a velocity of 5 m/s, and the pressure is 4.8 kPa gage. At both sections b and c the...

Q:

1. Water at 93.3C is being pumped from a large storage tank at 1atm abs at a rate of 0.189m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 1.49kW. The water...

Q:

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

Q:

ATTEMPT ALL QUESTIONS. BE SURE TO ANSWER A body with mass m = 1 2 kg is attached to the end of a spring that is stretched 2 m by a force of 100 N. Furthermore, there is also attached a dashpot4 that...

Q:

A pump delivers 2.5 liters/ second of water at 30C via a pipe of 50 mm diameter and surface roughness 0.5mm. The water is drawn from a tank maintained at atmospheric pressure and delivered to a tank...

Q:

5.16 Water flows steadily through the horizontal 30 pipe bend shown below. At station 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gage. At station 2, the diameter is...

Q:

5.16 Water flows steadily through the horizontal 30 pipe bend shown below. At station 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gage. At station 2, the diameter is...

Q:

Let V be a subset of X. a) Prove that V is open in X if and only if there is a collection of open balls {Ba: a A} such that b) What happens to this result if open is replaced by closed? V = U Bu- aEA

Q:

Total Quality Management (TQM) is a concept that was developed in Japan. When implemented correctly, the system can improve an organisation's reputation. Windhoek Car Manufacturers ("WCM") is a newly...

Q:

Sebastian is an addictions counseloc. He has a client that he thinks would benefit from a 1 2 - step group. Despite his knowledge of all the disadvantages of 1 2 - step groups, Sebastian still...

Q:

from the article, answer the question below : 1- Explain " exploration for and evaluation of mineral resources " in accordance with IFRS 6. 2- Describe how exploration and evaluation assets ?...