Question: Which factor does not affect the bond strength between concrete and reinforcement? a ) Surface roughness of reinforcement b ) Diameter of reinforcement c )

Which factor does not affect the bond strength between concrete and reinforcement?
a) Surface roughness of reinforcement
b) Diameter of reinforcement
c) Concrete cover thickness
d) Temperature of the concrete

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

Q:

The floor plan of an office building is shown below. The design specification are as follows, Characteristic strength of concrete 25 N/mm Characteristic strength of steel bar 500 N/mm Brickwall 110...

Q:

A concrete square footing is to be cast on a blinding layer to support a 400 x 300 mm concrete column. Using the following information: Base thickness h = 450 mm Axial dead load = 900 KN and axial...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

Calculate the required area of steel reinforcement for a concrete column with a cross - sectional area of 4 0 0 mm x 4 0 0 mm and a design axial load of 1 2 0 0 kN , using Fe 4 1 5 steel. Determine...

Q:

XXXX=4755(Use the value) Create a code in Python for a Reinforced Concrete Design where the following requirements are required: a) Asking for the input for the dimension of the beam and the...

Q:

I have 60 minutes sir. QUESTION 1) (60P) Concrete is filled into a steel pipe with a wall thickness of 5 mm and an inner diameter of 1200 mm. The steel pipe does not carry axial load. The circular...

Q:

Disks of polycarbonate plastic from a supplier are analyzed for scratch and shock resistance. The results from 100 disks are summarized as follows: Shock resistance High Low Scratch high 70 9...

Q:

Burke Company has a break-even of $600,000 in total sales. Assuming the company sells its product for $50 per unit, what is its margin of safety in units if sales total $800,000?

Q:

RST is a triangle. RS = 5 cm, RT = 6 cm. a If ST = 9 cm, use a diagram to show that angle R is obtuse. Write the size of angle R. b If angle R is obtuse what can you say about the length of ST? Give...

Q:

Bangor Moving Company is thinking of opening a new warehouse, and the key data are shown below. The company owns the building that would be used, and it could sell it for $100,000 after taxes if it...