Question: write a program using Arduino Uno and a KeyPad to control 2 LEDs. The LEDs are connected to pin 10 and 11. The sketch will

write a program using Arduino Uno and a KeyPad to control 2 LEDs. The LEDs are connected to pin 10 and 11. The sketch will work as follows: three keys from the KeyPad are used only. So, if key 1 is pressed then LED 1 only be ON, and if key 2 is pressed then LED 2 only be ON, and if key 3 is pressed then the two LEDs will be OFF.

(draw for the program)

yes

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Databases Questions!

In this assignment, you will develop a simple traffic light control system for a four - way street intersection using Arduino Uno board. At the minimum, you must prepare 2 sets of traffic lights (...

CECS 346 Project 3 A Smart Home By Dr. Min He Preparation: You will need two LaunchPads, 3 stepper motors with drivers (can be checked out from the instructor), 2 obstacle avoidance sensors (can be...

Part 2. Write a program that implements a simple color selector using the RGB LED Components: - 1x Joystick - 1x 10 k2 resistor (for joystick pushbutton) 1x RGB LED - 2x 220 resistors (for the LEDs)...

Final Pseudo Code: (Please follow the Final Project instructions to install and verify each component is working properly before trying to write a large program to get all components to work...

Computer Architecture and Organization Introduction to the Arduino Microcomputer Equipment: Arduino UNO microcomputer, PC with Arduino IDE installed, and a USB cable. Prototyping components and...

EE112 - Embedded Systems Lab 3 Spring 2020 EE112 - Embedded Systems Lab 3 Spring 2020 Last Name: First Name: Grading Scheme 1 points - Attending and Participating in Lab 2 points - Code...

Part 1 - You will use the Arduino analogWrite function to control the brightness of LEDs, display the analog pin voltage, and the current through the led. This sketch uses the analogWrite function to...

Hello, I'm working with an arduino UNO and am using (2) potentiometers, one that changes to different colors as I rotate the potentiometer and the other controls how bright or dim the RGB led gets...

Just an Arduino code using PORTB declarations and array for the passwords A device is used to control the access to a room. Employees need to swipe their ID cards in order to unlock the door. The...

A servo motor (or "servo") is a continuous DC motor packaged together with reduction gears, a potentiometer to measure rotation, and electronics connecting the potentiometer output to the motor drive...

(a) The buyer knows she will require financing to complete the purchase on the home she is contracting to buy. She carefully explains this to her broker, the seller and the listing broker. Her...

What alcohols are obtained from the reduction of the following compounds with sodium borohydride? a. 2-methylpropanal b. Cyclohexanone c. Benzaldehyde d. Acetophenone

4. Provide two examples of costs that are likely to be variable costs.

ty 8. (18 pts.) The reaction of isoprene (I) with m CPBA produces one of two possible epoxides (M or N) as the major product, the 1H NMR of which is shown below. \[ \text { _nnax } O \text { O. } \]...

=+ 3. Prove each of the following statements about the steady state of the Solow model with population growth and technological progress.

=+ b. What is the marginal product of capital in the initial steady state?

=+ a. What must the saving rate be in the initial steady state? [Hint: Use the steady-state relationship, sy = ( + n + g)k.]