Question: Determine centroid ( X, Y) of the cross section shown in Fig.3. below. For Values of X, and Y, see the table below. 150

Determine centroid ( X, Y) of the cross section shown in Fig.3. below. For Values of X, and Y, see the table below. 150 mr X, mm 20 mm 150 mm X1 mm Y mm 10 mm M 10 mm Fig.3 300 mm A. X1 = 173, Y = 173

Step by Step Solution

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock blur-text-image

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Civil Engineering Questions!

The hollow shaft has the cross section shown and is made of an elastic perfectly plastic material having a yield shear stress of t Y . Determine the ratio of the plastic torque T p to the maximum...

The Colorado River System Aqueduct has the cross section shown in Fig. P7.1. When the water in the aqueduct is 10.2 ft deep, flow is measured as 1600 cfs. If n = 0.014, what is SQ in (a) ft/ft and...

A welded steel girder having the cross section shown in the figure is fabricated of two 300mm x 25mm flange plates and a 800mm x 16mm web plate. The plates are joined by four fillet welds that run...

The aluminum strut is 10 mm thick and has the cross section shown. If it is subjected to a shear of V = 150 N, determine the shear flow at points A and B. 10 mm 40 mm 10 mm t+-40 mm- 30 mm 30 mm 10...

A storm drain has the cross section shown in Fig. P10.31 and is laid on a slope 1.5 m/km. If it is constructed of brickwork, find the normal discharge when the water level passes through the center...

A beam of wide-flange shape, W 8 x 28, has the cross section shown in the figure. The dimensions are b = 6.54 in., h = 8.06 in., tw = 0.285 in., and tf = 0.465 in. The loads on the beam produce a...

Solve the given problems. Suppose that a 5250-lb force is applied to a hollow steel cylindrical beam that has the cross section shown in Fig. 2.92. The stress on the beam is found by dividing the...

The subject of the project is an overhang beam presented in Fig. 1a. The beam is hinged supported at point a and supported by the bar at point c. The cross section is presented in Fig. 1b. The load...

A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location (xc, yc) of the centroid of the cross section. The dimensions are indicated at the center thickness...

The shaft is supported by a thrust bearing at A and journal bearing at D. If the shaft has the cross section shown, determine the absolute maximum bending stress in the shaft. 40 mm 25 mm D. 0.75 m...

The Westchester Chamber of Commerce periodically sponsors public service seminars and programs. Currently, promotional plans are under way for this year's program. Advertising alternatives include...

Suman Corporation In mid-April, Mike Bradie, vice president of supply chain management at Suman Corporation (Suman), had become increasingly concerned about the potential shortage of supply of barac,...

Briefly describe the main purpose of normalization in database design. (3 marks) (6 marks) (b) Describe the rules of one normal form (INF), 2 NF and 3 NF. (c) You work as an administrator in UCSI Pet...

Take a few moments to write down all the ways people could get hurt at work. Then categorize them into the following categories in table/chart: Chemical Biological Physical Ergonomics Psychosocial

An analysis of transactions for Blossom Company, a certified public accounting firm, for the month of August is as follows. Assume that August is the company's first month of business. Assets...

Your (all equity) firm sells 35,000,000 units at $2.30 per unit, the variable cost per unit is $1.84, and fixed costs are $6,500,000, giving your firm a DOL of 1.6771. The firm faces a tax rate of 40...

On July 1, 2020 The Corporation issued bonds with a face value of $400,000. The bonds carry a face interest rate of 8 percent that is payable each July 1 and January 1. a. Prepare the entry in...

Write electron configurations for the following ions, and determine which have noble-gas configurations: (a) Cd2+ (b) p3- (c) Zr4+ (d) Ru3+ (e) As3- (f) Ag+

The 2014-T6 aluminium rod has a diameter of 30 mm and supports the load shown. Determine the displacement of end A with respect to end E. Neglect the size of the couplings. 8 kN 2 kN 6 kN 4 kNY -2m-...

The shaft is made of A992 steel and has an allowable shear stress of Ï allow = 75 MPa. When the shaft is rotating at 300 rpm, the motor supplies 8 kW of power, while gears A and B withdraw 5 kW...

The shaft is subjected to a distributed torque along its length of t = (10x 2 ) N m/m, where x is in meters. If the maximum stress in the shaft is to remain constant at 80 MPa, determine the required...

3.41. In 2004, the five-numbersummary forthe statewide percentage ofpeople without health insurance had a minimum of 8.9% (Minnesota), Ql = 11.6, Med = 14.2, (93 = 17.0, and maximum of 25.0% (Texas)...

3.40. Infant mortality rates (number of infant deaths, per 1000 live births) are reported by the UN. In their 2006 report, the values for Africa had a five-number summary of min 54,Q1 - 76, median -...

3.39. For the student survey data on number of times a week reading a newspaper, referred to in Exercise 1.11, Figure 3.20 shows a computer printout of the stem-and-leaf plot and the box plot. (a)...