Question: The shear shown is used to trim electronic-circuit-board laminates. Neglecting the thickness of the shearing blade and knowing that a vertical 3-kN shearing force at

The shear shown is used to trim electronic-circuit-board laminates. Neglecting the thickness of the shearing blade and knowing that a vertical 3-kN shearing force at E is required to cut the laminate, determine

(a) The magnitude of the applied force P,

(b) The reaction at C.

30 300 mm в 60 mm 25 mm 30 mm

30 300 mm 60 mm 25 mm 30 mm

Step by Step Solution

★★★★★

3.50 Rating (177 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

FBD Blade 3kN EBD F 0 3 kN 12 FBD 0 FBD 325 kN C 13 FBD ABC IR 030m ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

4-E-M-E-VM (716).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The shear shown is used to trim electronic-circuit-board laminates. Knowing that P = 400 N, determine (a) The vertical component of the force exerted on the shearing blade at D, (b) The reaction at...

The shear shown is used to cut and trim electronic-circuit-board laminates. Knowing that the coefficient of kinetic friction between the blade and the vertical guide is 0.20, determine the force...

The double-toggle latching mechanism shown is used to hold member G against the support. Knowing that α = 60°, determine the force exerted on G. 15

Please provide solution to all the questions, Thank you! Q) The reinforced concrete building shown int the below figure is located in Ras Al Khaimah. The building is used as a shelter during...

Computer study of the behavior of multistory building frames. The object of this study is to examine the behavior of building frames fabricated with two common types of connections. When open...

Problem 1 . Consider the four - story office building with story height of 1 2 ' and plan shown below, located on soil type C in Santa Monica, California. The floor and roof loads are 1 0 0 psf and 8...

Brackets, such as the one shown, are used in mooring small watercraft. Failure of such brackets is usually caused by bearing pressure of the mooring clip against the side of the hole. Our purpose...

Problem 4 : Brackets, such as the one shown, are used in mooring small watercraft. Failure of such brackets is usually caused by bearing pressure of the mooring clip against the side of the hole. Our...

Problem 4 . NO MORE INFORMATION PROVIDED The 1 6 2 2 2 5 - m m rubber blocks shown are used in a double - U shear mount to isolate the vibration of a machine from its supports. An applied load of P =...

Total June 2013 sales for Roys Catering are expected to be $500,000. Of each months sales, 80 percent is expected to be on credit. The Accounts Receivable balance at May 31 is $119,600, of which...

Suppose that the following constraints have been provided for a linear programming model. and x1 0, x2 0. (a) Demonstrate that the feasible region is unbounded. (b) If the objective is to...

Identify the slope from the following equation Y = 7 x 1 4 7 Y 1 4 X none of the above

A 2-kg piston accelerates to 20 m/s from rest. What constant gas pressure is required if the area is 10 cm 2 , the travel is 10 cm, and the outside pressure is 100 kPa?

A dilatometer test was conducted in a clay deposit. The groundwater table was located at a depth of 3 m below the surface. At a depth of 8 m below the surface, the contact pressure (P 0 ) was 280...

Beginning inventory, purchases, and sales for J101 are as follows: Assuming a perpetual inventory system and using the weighted average method, determine (a) The weighted average unit cost after the...

A four-stroke gasoline engine runs at 1800RPM with a total displacement of 150 in. 3 and a compression ratio of 10:1. The intake is at 520 R, 10 psia, with a mean effective pressure of 90 psia. Find...

The effective life of insulating fluids at an accelerated load of 35 kV is being studied. Test data have been obtained for four types of fluids. The results were as follows: (a) Is there any...

5. Consider a sample with data values of 27, 25, 20, 15, 30, 34, 28, and 25. Compute the 20th, 25th, 65th, and 75th percentiles.

A utility hook was formed from a 1-in-diameter round rod into the geometry shown in the figure. What are the stresses at the inner and outer surfaces at section A-A if the load F is 1000 lbf? in 10...

The steel eyebolt shown in the figure is loaded with a force F of 100 lbf. The bolt is formed of ¼ -in-diameter wire to a 3/8 -in radius in the eye and at the shank. Estimate the stresses at...

Shown in the figure is a 12-gauge (0.1094-in) by ¾ -in latching spring that supports a load of F = 3 lbf. The inside radius of the bend is 1/8 in. Estimate the stresses at the inner and outer...

The Barb Akew is a famous local barbeque restaurant. It is examining whether it should buy a new kitchen. Its purchase price is $ 5 7 5 , 0 0 0 and will be depreciated straight line to a value of $ 2...

If a company has an unappealingly low market share of entry-level cameras sales in North America because it is being outcompeted by various rival companies, then company managers should increase the...

Beach Limited is a subsidary of Golden Limited . When Golden acquired its 70% interest in Beach , the retained earnings of Beach Limited were $40,000. At the beginning of the current period, Beach...