Question: The figure shows a rectangular member OB, made from ¼-in-thick aluminum plate, pinned to the ground at one end and supported by a ½ -in-diameter

The figure shows a rectangular member OB, made from ¼-in-thick aluminum plate, pinned to the ground at one end and supported by a ½ -in-diameter round steel rod with hooks formed on the ends. A load of 100 lbf is applied as shown.

Use superposition to determine the vertical deflection at pointB.

C 100 Ibf -in dia. 12 in -in thick in |+--7 in 12in-

Step by Step Solution

★★★★★

3.40 Rating (156 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

EMO06 FAC 11100 FAC 1833 lbf The deflection at point A in the neg... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

233-M-E-D-S (129).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The figure shows a rectangular member OB, made from ¼ -in-thick aluminum plate, pinned to the ground at one end, and supported by a ½ -in-diameter round steel rod that is formed into an...

A vertical tube is closed at one end and open to air at the other end. The air pressure is 1.01 105 Pa. The tube has a length of 0.75 m. Mercury (mass density = 13 600 kg/m3) is poured into it to...

The figure shows a steel pressure cylinder of diameter 4 in which uses six SAE grade 5 steel bolts having a grip of 12 in. These bolts have a proof strength (see Chap. 8) of 85 kpsi for this size of...

Solve Prob. 451 using Castiglianos theorem. Prob. 451, The figure shows a rectangular member OB, made from ¼-in-thick aluminum plate, pinned to the ground at one end and supported by a...

Solve Prob. 450 using Castiglianos theorem. Prob. 450, The figure shows a rectangular member OB, made from ¼-in-thick aluminum plate, pinned to the ground at one end and supported by a...

Repeat Prob. 486 for the vertical deflection at point A. Prob. 486, The figure shows a rectangular member OB, made from -in-thick aluminum plate, pinned to the ground at one end, and supported by a ...

The figure shows a rectangular member O B , made from 1 4 - in - thick aluminum plate, pinned to the ground at one end and supported by a 1 2 - in - diameter round steel rod with hooks formed on the...

( textbook , problem 4 - 8 6 , use the materials properties in the table below ) The figure shows a rectangular member O B , made from 1 4 - in - thick aluminum plate, pinned to the ground at one...

The figure shows a rectangular member OB , made from 0 . 5 - cm thick aluminum plate, pinned to the ground at one end and supported by a coil spring at point A . The spring has been measured to...

The figure shows an aluminum beam OB with rectangular cross section, pinned to the ground at one end and supported by a round steel rod with hooks formed on the ends. A load is applied as shown. Use...

On January 1, a machine with a useful life of four years and a salvage value of $ 26000 was purchased for $ 156000 . What is the depreciation expense for year 2 under straight-line depreciation? $...

Jonathan's business for the year ended 2022 showed the accounts as below. Calculate net assets of the business. Accounts $30,000 payables Accounts $59,500 receivables Cash at $12,000 bank Net assets...

Which of the following programming languages was designed by a single person? Question 9 options: C Algol PL / 1 Cobol

Two models are applied to a dataset that has been partitioned. Model A is considerably more accurate than model B on the training data, but slightly less accurate than model B on the validation data....

A 50-mm-deep hole, 25 mm in diameter, is being produced by electrochemical machining. Assuming that a high production rate is more important than the quality of the machined surface, estimate the...

If the operation in Problem 9.66 were per-formed on an electrical-discharge machine, what would be the estimated machining time?

A cutting-off operation is being performed with a laser beam. The workpiece being cut is 1/4 in. thick and 4 in. long. If the kerf is 1/6 in. wide, estimate the time required to perform this...

You are considering purchasing shares in a mutual fund. In detail, what are three advantages and three disadvantages of mutual fund investing that are important for potential investors to consider?

Wine and Roses, Inc. offers a 7% coupon bond with semiannual payments and a yield to maturity of 7.73%. The bonds mature in 9 years. What is the market price of a $1,000 face value bond? $1,108.16...

A community college has estimated that it needs $480,000 in 5 years to remodel their student gym. To save for the estimating remodeling costs, they decide to make payments into an account at the end...