Question: Two steel tubes are shrink-fitted together where the nominal diameters are 1.50, 1.75, and 2.00 in. Careful measurement before fitting revealed that the diametral interference

Two steel tubes are shrink-fitted together where the nominal diameters are 1.50, 1.75, and 2.00 in. Careful measurement before fitting revealed that the diametral interference between the tubes to be 0.00246 in. After the fit, the assembly is subjected to a torque of 8000 lbf .in and a bending- moment of 6000 lbf .in. Assuming no slipping between the cylinders, analyze the outer cylinder at the inner and outer radius. Determine the factor of safety using distortion energy with Sy = 60 kpsi.

Step by Step Solution

★★★★★

3.43 Rating (162 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

E 30106 psi v 0292 I 6424 154 05369 in Eq 357 can be written in terms of diame... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

M-E-F-R (38).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The plastic hexagonal tube is subjected to a torque of 150 N m. Determine the mean dimension a of its sides if the allowable shear stress is Ï allow = 60 MPa. Each side has a thickness of t = 3...

The plastic tube is subjected to a torque of 150 N m. Determine the average shear stress in the tube if the mean dimension a = 200 mm. Each side has a thickness of t = 3 mm. 150 N-m

The plastic tube is subjected to a torque of 150 N m. Determine the mean dimension a of its sides if the allowable shear stress is Ï allow = 60 MPa. Each side has a thickness of t = 3 mm. 150 N-m

Design of a twobar truss Design a symmetric twobar truss both members have the same crosssection as shown in Fig E216 to support a load W The truss consists of two steel tubes pinned together at one...

2 . 1 3 Design the steel framework shown in Fig. E 2 - 1 3 at a minimum cost. The cost of a horizontal member in one direction is $ 2 0 w and in the other direction it is $ 3 0 d . The cost of a...

Question 2 (10 marks) Two steel tubes are connected together by an adhesive joint and loaded with force P, as shown in Figure Q2. The maximum allowable shear stress for the adhesive material is 5...

Design of a two - bar truss. Design a symmetric two - bar truss ( both members have the same cross section ) shown in Fig. 1 to support a load W . The truss consists of two steel tubes pinned...

COMPANY OVERVIEW Headquartered in Canton, Ohio, The Timken Corporation was a worldwide producer of anti- friction bearings and steel. The company's businesses were organized into three segments:...

Chairvana's Table Assembly Operations: pairs of hole-punched tubes in a work-in-process storage area waiting for the bending operation Chaicvana Inc. manufactures metal tables and chairs at its plant...

Given the probability function P(x) = 5 x/ 10 for x _ 1, 2, 3, 4 find the mean and standard deviation.

Explain why it is important for audit documentation to include each of the following: identification of the name of the client, period covered, description of the contents, initials of the preparer,...

Which type of bank would be subject to the highest risk - based capital requirements? G - SIBs large banks banks that fail the Fed's stress test N / A: all banks face the same capital requirements

On December 29, 2022, an employee received a $5,000 check from her employers client. The check was payable to the employer. The employee did not remit the funds to the employer until December 30,...

What is a way to validate transactions and achieve a distributed consensus? Blockchain distributed, computing proof of work or proof of Stake

Use your ti calculator to write down commands for b A hypotheses test, some information from one sample, and a standard error from a randomization distribution are provided. avalgib noming s...

Investors require an 8% rate of return on Mather Company's stock (i.e., r = 8%). a. What is its value if the previous dividend was Do = $1.00 and investors expect dividends to grow at a constant...