Question: What is a stress raiser?

What is a "stress raiser"?

Step by Step Solution

★★★★★

3.48 Rating (161 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Stress raisers are changes in material shape part ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Document Format (1 attachment)

Word file Icon

916-E-M-S-E-M-S (1890).docx

120 KBs Word File

Students Have Also Explored These Related Materials Science Engineering Questions!

Q:

A fatigue test was conducted in which the mean stress was 50 MPa (7250 psi) and the stress amplitude was 225 MPa (32,625 psi). (a) Compute the maximum and minimum stress levels. (b) Compute the...

Q:

A single crystal of a BCC metal is oriented so that the [001] direction is parallel to the applied stress. If the critical resolved shear stress required for slip is 12, 000 psi, calculate the...

Q:

A stress measurement made in a deep borehole at a depth of 500 m (1,640 ft) indicates a horizontal stress that is three times the vertical stress and that the vertical stress is consistent with an...

Q:

Q 1 ( 4 0 Points ) A steel plate ( Young ' s Modulus: 2 0 0 GPa, Poisson's ration: 0 . 3 3 ) with dimensions 3 0 mm wide, 4 0 mm long, and 5 mm thick has a 1 0 - mm diameter hole in the center and a...

Q:

Problem 3. (verso) Objective. To determine displacements and stresses in a plate, loaded (strained) in its own plane, using constant strain triangle (CST) finite elements. To observe areas of high...

Q:

Problem 3 . ( verso ) Objective. To determine displacements and stresses in a plate, loaded ( strained ) in its own plane, using constant strain triangle ( CST ) finite elements. To observe areas of...

Q:

Problem 3 . ( verso ) Objective. To determine displacements and stresses in a plate, loaded ( strained ) in its own plane, using constant strain triangle ( CST ) finite elements. To observe areas of...

Q:

The wing to fuselage attachment bracket of a transport aircraft ( Fig . 1 ) is made of AISI 4 3 4 0 , for which the mechanical and fatigue properties are shown in Figure 2 . This structure is...

Q:

We consider an "infinite" plate under cyclic loading characterized by: R=1(=a)=100MPanominalstress The fatigue properties of the material ( R=1, smooth samples) are listed in the table below...

Q:

The Ti - 6 Al - 4 V alloy is used to make a cylindrical pressure vessel having closed ends with an inner diameter of 2 5 0 mm and wall thickness of 2 . 5 mm . ( a ) What repeatedly applied pressure...

Q:

find the cabic spline For Following datas ? and compute y (1:5)? X1 X JO y 20 1 Yo -8 d y -1 22. 3 42. +18.

Q:

To the closest year, how long will it take $200 to double if it is deposited and earns the following rates? [Notes: (1) See the hint for Problem 2-1. (2) This problem cannot be solved exactly with...

Q:

Have you ever been the victim of a companys poor customer service policy, as either an external or internal customer? What specifically occurred? How did this treatment make you feel? What would you...

Q:

The output select sellers selected sellers identifies those sellers that have been judged to be in a competitive range based upon the outcome of the proposal or bid evaluation and that have...

Q:

A piston/cylinder contains 1 kg of liquid water at 20C and 300 kPa. Initially the piston floats, similar to the setup in Problem 4.64, with a maximum enclosed volume of 0.002 m3 if the piston touches...

Q:

Refrigerant-12 is contained in a piston/cylinder arrangement at 2 MPa, 150C with a mass less piston against the stops, at which point V = 0.5 m3. The side above the piston is connected by an open...

Q:

A piston/cylinder (Fig P4.114) contains 1 kg of water at 20C with a volume of 0.1 m3. Initially the piston rests on some stops with the top surface open to the atmosphere, Po and a mass so a water...

Q:

The Barb Akew is a famous local barbeque restaurant. It is examining whether it should buy a new kitchen. Its purchase price is $ 5 7 5 , 0 0 0 and will be depreciated straight line to a value of $ 2...

Q:

If a company has an unappealingly low market share of entry-level cameras sales in North America because it is being outcompeted by various rival companies, then company managers should increase the...

Q:

Beach Limited is a subsidary of Golden Limited . When Golden acquired its 70% interest in Beach , the retained earnings of Beach Limited were $40,000. At the beginning of the current period, Beach...