Question: (a) Design the optimal conical container (Figure) that has a cover and has walls of negligible thickness. The container is to hold 0.5 m3. Design

(a) Design the optimal conical container (Figure) that has a cover and has walls of negligible thickness. The container is to hold 0.5 m3. Design it so that the areas of its top and sides are minimized.

(b) Repeat (a) but for a conical container without acover

Lid

Step by Step Solution

★★★★★

3.48 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a The area and volume can be computed as An Excel spreadsheet can be set up to ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

45-M-N-A-O (48).docx

120 KBs Word File

Students Have Also Explored These Related Numerical Analysis Questions!

A 1 m3 container is filled with 400 kg of granite stone, 200 kg dry sand and 0.2 m3 of liquid 25C water. Use properties from tables A.3 and A.4 and use air density of 1.1 kg/m3. Find the average...

A 5 m3 container is filled with 900 kg of granite (density 2400 kg/m3) and the rest of the volume is air with density 1.15 kg/m3. Find the mass of air and the overall (average) specific volume.

A rigid container has two rooms filled with water, each 1 m3 separated by a wall. Room A has P = 200 kPa with a quality x = 0.80. Room B has P = 2 MPa and T = 400C. The partition wall is...

Please solve this using matlab and type in the codes here Design the optimal cylindrical container that is close at both ends and has walls of negligible thickness. The container is to hold 1 m^3....

Design the optimal cylindrical tank with dished ends (Fig. P16.3). The container is to hold 0.5 m3 and has walls of negligible thickness. Note that the area and volume of each of the dished ends can...

Design the optimal cylindrical tank with dished ends (see figure below). The container is to hold 0.5 m3 and has walls of negligible thickness. Note that the area and volume of each of the dished...

Week 3: No Plagiarism No content from other students papers. Post should be in APA 6th edition format, I will need References and in-text citations. This website should be useful for all APA...

Chapter 5: Hazardous Waste Site Clean-Up Technologies IN THIS CHAPTER Treatment technologies for contaminated hazardous waste sites Containment technologies for contaminated sites Innovative...

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

F&D Manufacturing company increases all its inputs by 50 percent each. If F&D's output increases by 100 percent, then F&D is experiencing (A) increasing returns to scale (B) constant...

a. Explain how effective internal control is over financial statement accounts whose measurement requires significant estimation (5%). b. PSAK 68: Fair Value Measurement stipulates that there is a...

2.33 If a multiple-choice test consists of 6 questions, each with 4 possible answers of which only 1 is correct, (a) in how many different ways can a student check off one answer to each question?...

The month in which the year's highest temperature occurs in a city has probabilities in the ratio 1:3:6:10 for May, June, July, and August, respectively. Find the probability that the highest...

James Corporation's balance sheet at December 31, 2018, is presented below. During 2019, the following transactions occurred. 1. James paid $2,500 interest on the bonds on January 1, 2019. 2. James...

Refer to the data in Exercise 109. Assume that instead of producing 3,000 bottles of Clean-All during the month, the company produced only 2,000 bottles, using 16,000 millilitres of material. (The...

Explain how regulatory lag can lead to a regulated firm operating in ways and under conditions that both the firm and the regulatory body might not desire.

Ross Hopkins is attempting to monitor a filling process that has an overall average of 705 cc. The average range is 6cc. If you use a sample size of 10, what are the upper and lower control limits...

If bleached human bones found lying in the desert were carefully examined, would osteons be present? How about osteocytes and a marrow cavity?

Determine the values of the following percentiles: X20.05,10, X20.025,15, X20.095,20, X20.099,18, X20.995,16, and X20.005,25,

Determine the 2 percentile that is required to construct each of the following CIs: (a) Confidence level = 95%, degrees of freedom = 24, one-sided (upper) (b) Confidence level = 99%, degrees of...

A rivet is to be inserted into a hole. A random sample of n = 15 parts is selected, and the hole diameter is measured. The sample standard deviation of the hole diameter measurements is s = 0.008...

JETA Company tiene un tiempo de ciclo de 3 das, utiliza una cuenta sin procesar y en proceso (RIP) y carga todos los costos de conversin al costo de los bienes vendidos. Al final de cada mes, se...

Assume that your parents wanted to have $180,000 saved for college by your 18th birthday and they started saving on your first birthday. They saved the same amount each year on your birthday and...

As evidenced by Table 4 from Agarwal and Naik (2004, Risks and portfolio decisions involving hedge funds, Review of Financial Studies ) provided above: Explain the implications of hedge funds'...