A power transmission system is modeled as shown in Fig 9 92 Given the following Source voltage Vs 115 0o V, Source impedance Zs 1 j0 5 Icirc copy , Line impedance Zl 0 4 j0 3 Icirc copy , Load impedance ZL 23 2 j18 9 Icirc copy , Find the load current IL Zi 1, 7 Zi Source Transmission ine Load

Question: A power transmission system is modeled as shown in Fig. 9.92. Given the following; Source voltage ............................... Vs = 115 0o V, Source impedance ...........................

A power transmission system is modeled as shown in Fig. 9.92. Given the following;
Source voltage ............................... Vs = 115 ˆ 0o V,
Source impedance ........................... Zs = 1 + j0.5 Î©,
Line impedance .............................. Zl = 0.4 + j0.3 Î©,
Load impedance ............................ ZL = 23.2 + j18.9 Î©,
Find the load current ........................ IL‹…

Zi 1, 7. Zi Source Transmission ine Load

Step by Step Solution

★★★★★

3.44 Rating (170 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Z Z s 2Z Z L Z 1 08 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

905-P-E-M-C (967).docx

120 KBs Word File

Students Have Also Explored These Related Electricity and Magnetism Questions!

For the electric power transmission system shown in Fig. 21-25, what is the ratio NS / NP for (a) The step-up transformer, (b) The step-down transformer next to the home? High voltage transmission...

Repeat Problem 9.31(a) for the common-gate compensation scheme in Fig. 9.22 a. Data from Prob. 9.31 (a): The Miller-compensated two-stage op amp in Fig. 9.25 can be modeled as shown in Fig. 9.26. In...

The Miller-compensated two-stage op amp in Fig. 9.25 can be modeled as shown in Fig. 9.26. In the model, let g m1 = 0.5 mA/V, R 1 = 200 kÎ©, g m6 = 2 mA/V, R 2 = 100 kÎ©, C 1 =...

Each min, the main display of control room that monitors a certain power transmission system reports the state of the power loads. The data on display shows that the distribution system may be in (0)...

please do it 4 hour will upvote A speed reducer is to be designed for a Power Transmission System used in a small equipment. According to the lay-out given below, the pulley M is the driver pulley...

A simple power transmission system shown in Figure Q2 has two transmission lines. It is assumed that Vs = VR = 132 kV, f = 50Hz, phase shift 8 = 25, X = 50 % on a 132 kV/100 MVA base. 2.1 Calculate...

Calculating Power in Decibels. In an optical communications system or electrical power transmission system, the power or signal often is transferred between several components. The decibel (dB) is a...

You are to design a power transmission system for a wind turbine. The input is a wind turbine whose torque input is assumed at 34 N-m at 250 rpm. The turbine is fitted on to the same input shaft as a...

"A countrywide blackout has been caused by a sudden plunge in the frequency in the power transmission system," Pakistan's power minister, Omar Ayub Khan, wrote on Twitter in the early hours of...

Exercise 7-3: Maximization of real power absorbed by the load Consider the circuit model of an AC power transmission system shown in Figure 7-6 again. Now the load consists of a 3.3mH inductor...

Use the ALEKS calculator to solve the following problems. (a) Consider at distribution with 10 degrees of freedom. Compute P (-1,93

Auto-Delivery provides expedited delivery of auto parts to car repair shops throughout the city. To accomplish this, AutoDelivery has a fleet of ten pickup trucks of various makes. Every truck has...

The decisions in the Applegate and Jenkins cases are relevant when determining: A . The residency of an individual taxpayer using the Ordinary concepts ( or 'Resides in Australia' ) test. B . The...

4. Assume the economy is operating at a real GDP below full-employment real GDP. Keynesian economists would prescribe which of the following policies? a. Noninterventionist b. Fixed rule c....

A steel wire of diameter 1 mm can support a tension of 0.2 kN. A cable to support a tension of 20 kN should have diameter of what order of magnitude?

A child slides across a floor in a pair of rubber-soled shoes. The friction force acting on each foot is 20.0 N. The footprint area of each shoe sole is 14.0 cm2, and the thickness of each sole is...

A 30.0-kg hammer strikes a steel spike 2.30 cm in diameter while moving with speed 20.0 m/s. The hammer rebounds with speed 10.0 m/s after 0.110 s. What is the average strain in the spike during the...

Advance, Inc., is trying to determine its cost of debt. The firm has a debt issue outstanding with 12 years to maturity that is quoted at 104 percent of face value. The issue makes semiannual...

What are the pros and cons of UML? and Why is Quality assurance critical to the success of a project?

Calculate the correlation coefficient, r. Round your answer to three decimal places. Hours Spent Studying 0.5 1 1.5 2 2.5 3 4.5 5 5.5 6 Midterm Grades 60 63 69 72 75 78 87 93 96 99