Question: A rectangular cantilever beam 75 mm high, 25 mm wide, and 1 m long is subjected to a concentrated force of 100 N at its

A rectangular cantilever beam 75 mm high, 25 mm wide, and 1 m long is subjected to a concentrated force of 100 N at its end. Select two different unreinforced and reinforced materials from Table 10.1 and calculate the maximum deflection of the beam. Then select aluminum and steel, and for the same beam dimensions, calculate the maximum deflection. Compare and comment on the results?

Step by Step Solution

★★★★★

3.48 Rating (174 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Calculate the deflection D PL 3 3EI 1 Where d is the deflection P is the load E is the e... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

972-E-M-E-B-D (944).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A propped cantilever beam of length L = 54 in. with a sliding support supports a uniform load of intensity q (see figure). The beam is made of steel (ÏY = 36 ksi) and has a rectangular cross...

A cantilever beam AB supports a block which causes a static deflection of 40 mm at B. Assuming that the support at A undergoes a vertical periodic displacement = m sin ft, where m = 10mm, determine...

A cantilever beam AB is loaded by a couple Mo at its free end (see figure.) The length of the beam is L = 15 and the longitudinal normal strain at the top surface is 0.001. The distance from the top...

Need a well written Reflection paper. For class Compensation and Benefits (MGT3349) Download The attachment and follow the instruction Need a well written Reflection paper. For class Compensation and...

Q1 A simply supported beam has a concentrated downward force P at a distance of a from the left support, as shown in the figure below. The flexural rigidity EI is constant. Find the equation of the...

Computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 C to 3 0 C . Assume the specific...

computer Science Question 1 : Heat Exchanger Design Part A: Calculate the heat transfer rate required for a heat exchanger to cool 1 5 0 0 kg / hr of water from 8 5 \ deg C to 3 0 \ deg C . Assume...

Calculate the deflection of a simply supported beam with a span of 8 meters under a uniform load of 5 kN / m . Determine the factor of safety for a slope with an angle of 3 0 degrees, cohesion of 1 0...

4. Luis, no tiene . est . . . tenga est (usted) nervioso durante la entrevista.

In this problem you will use variation of parameters to solve the nonhomogeneous equation t'y" + 2ty 6y = - (2t + 3t) A. Plug y = t" into the associated homogeneous equation (with "0" instead of "-...

As an individual consumes more of a given good, the marginal utility of that good to the consumer a. rises at an increasing rate. b. rises at a decreasing rate. c. falls. d. rises.

1. In recent years, technological improvements have greatly reduced the costs of producing basic cell phones, and a number of new firms have entered the cell phone industry. At the same time, prices...

On the moon the gravitational acceleration is approximately one-sixth that on the surface of the earth. A 5-kg mass is weighed with a beam balance on the surface on the moon. What is the expected...

A 5 m 3 container is filled with 900 kg of granite (density 2400 kg/m 3 ) and the rest of the volume is air with density 1.15 kg/m3. Find the mass of air and the overall (average) specific volume.

A tank has two rooms separated by a membrane. Room A has 1 kg air and volume 0.5 m3, room B has 0.75 m3 air with density 0.8 kg/m3. The membrane is broken and the air comes to a uniform state. Find...

Tren Tyre Ltd deals in tyres for which the following information is available: Average usage 140 tyres per day Minimum usage 90 tyres per day Maximum usage 175 tyres per day Lead time 10 16 days...

Dividend decisions are complicated and involve the understanding of critical strategic factors that affect the policy and value of a firm. Thus, the management of any firm has to consider the...

1. True/False: Process mapping is primarily used to model relational databases. 2. True/False: When collecting information for a process map, the one-on-one interview method is generally preferred...