Question: A refrigerant is compressed by an adiabatic compressor operating at steady state to raise the pressure from 200 kPa to 750 kPa. The following data

A refrigerant is compressed by an adiabatic compressor operating at steady state to raise the pressure from 200 kPa to 750 kPa. The following data are supplied for the inlet and exit ports. Inlet: v = 0.0835 m3/kg, h = 182.1 kJ/kg, V = 30 m/s; Exit: v = 0.0244 m3/kg, h = 205.4 kJ/kg, V = 40 m/s. If the volume flow rate at the inlet is 3000 L/min, determine
(a) The mass flow rate.
(b) The volume flow rate at the exit.
(c) The compressor power.
(d) What-if Scenario: What would the power consumption be if the change in kinetic energy were neglected?

Step by Step Solution

★★★★★

3.45 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

a b At steady state c While the external work transfer is negati... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

861-ME-T (6875).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Steam is compressed by an adiabatic compressor from 0.2 MPa and 150C to 2.5 MPa and 250C at a rate of 1.30 kg/s. The power input to the compressor is (a) 144 kW (b) 234 kW (c) 438 kW (d) 717 kW (e)...

Steam is compressed by an adiabatic compressor from 0.2 MPa and 150oC to 0.8 MPa and 350C at a rate of 1.30 kg/s. The power input to the compressor is (a) 511 kW (b) 393 kW (c) 302 kW (d) 717 kW (e)...

Air is compressed by an adiabatic compressor from 95 kPa and 27C to 600 kPa and 277C. Assuming variable specific heats and neglecting the changes in kinetic and potential energies, determine (a) The...

5-43C Consider an adiabatic turbine operating steadily. Does the work output of the turbine have to be equal to the decrease in the energy of the steam flowing through it? 5-44C Consider an air...

Question 5 Question 1 An ideal Brayton cycle, operating between the pressure limits of 1 bar and 6 bar, has minimum and maximum temperatures of 300 K and 1500 K. The ratio of specific heats of the...

Question 1 A steam power cycle with regeneration as shown below on the T-s diagram employs a single open feedwater heater for efficiency improvement. The fluids mix with each other in an open...

Republic of Iraq Ministry of Higher Education and Scientific Research University of Technology Chemical Engineering Department MODELING AND SIMULATION OF FCC RISERS A RESEARCH SUBMITTED TO THE...

1. Explain the principles of facilities layout and list types of layout. 2.(a) Explain the symptoms of poor production planning and control in a manufacturing organisation. (b) Describe with example...

Assigned Problems A turbine receives steam at the following state: pressure 1 3 8 0 kPa ; specific volume 0 . 1 4 3 m 3 k g ; internal energy 2 5 9 0 k J k g ; velocity 3 0 m s . The state of the...

A certain industrial process requires a steady supply of saturated vapor steam at 200 kPa at a rate of 0.5 kg/s. Also required is a steady supply of compressed air at 500 kPa at a rate of 0.1 kg/s....

Beryllium chloride, BeCl2, is a solid substance consisting of long (essentially infinite) chains of atoms with Cl atoms in bridge positions. However, if the solid is heated, it forms a vapor of BeCl2...

CB-Brand Analysis assignment is designed to allow you to develop through researching a practically orientated project. This assessment offers the opportunity for you to tap into different aspects of...

51. A partial computer output from a regression analysis follows. The regression equation is Y = 8.13 + 7.602 XI + 3.111 X2 Predictor Coef SE Coef T Constant _______ 2.667 _____ X1 _______ 2.105...

Suppose the graphs of f sxd x2 and tsxd 2x are drawn on a coordinate grid where the unit of measurement is 1 inch. Show that, at a distance 2 ft to the right of the origin, the height of the graph...

Long cylindrical steel rods (Ï = 7833 kg/m3 and cp = 0.465 kJ/kg·°C) of 10-cm diameter are heat treated by drawing them at a velocity of 3 m/min through a 7-m-long oven maintained at...

The inner and outer surfaces of a 4-m 10-m brick wall of thickness 20 cm are maintained at temperatures of 16C and 4C, respectively. If the rate of heat transfer through the wall is 1250 W,...

A frictionless piston-cylinder device contains saturated liquid water at 40-psia pressure. Now 600 Btu of heat is transferred to water from a source at 1000F, and part of the liquid vaporizes at...

The next dividend payment by MUG inc will be $3.10 per share. The dividends are anticipated to maintain a 5% growth rate, forever. If MUG stock currently sells for $48.00 per share what is the...

Accessing SEC Reports and Calculating Ratios a . Use data from the companies' balance sheets and income statements to complete the following table. Round answers to the nearest million, when...

Three recent graduates of the computer science program at the university of Tennessee are forming a company that will write and distribute new application Software for the iPhone. Initially, the...