Question: A simply supported beam ABC is loaded by a vertical load P acting at the end of a bracket BDE (see figure). Draw the shear-force

A simply supported beam ABC is loaded by a vertical load P acting at the end of a bracket BDE (see figure).
Draw the shear-force and bending-moment diagrams for beam ABC.

IeI 2 4 4

Step by Step Solution

★★★★★

3.35 Rating (158 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

R 2 M 0 0 PL ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (405).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

A simply supported beam AB supports a trapezoidally distributed load (see figure). The intensity of the load varies linearly from 50 kN/m at support A to 25 kN/m at support B. Calculate the shear...

A simply supported beam loaded by two forces is shown in the figure. Select a pair of structural steel channels mounted back to back to support the loads in such a way that the deflection at midspan...

A beam ABCD consisting of a simple span BD and an overhang AB is loaded by a force P acting at the end of the bracket CEF (see figure). (a) Determine the deflection Î´A at the end of the...

4 . 5 - 8 A simply supported beam ABC is loaded by a vertical load P acting at the end of a bracket BDE ( see figure ) . ( a ) Draw the shear - force and bending - moment diagrams for beam ABC. ( b )...

4 . 5 . 7 A simply supported beam ABC is subjected to a vertical load P acting at the end of a bracket BDE ( see figure ) . a ) Draw the shear and bending moment diagrams for beam ABC. b ) Now assume...

A simply supported beam in Figure Q1(b) is pinned at point A and roller at point B. (CO2-POZ) (C3) i. Draw the Influence lines diagram for the reactions at support A and bending moment at point C. (6...

The simple beam AB supports a triangular load of maximum intensity q 0 =10 lb/in. acting over one-half of the span and a concentrated load P = 80 lb acting at midspan (see figure). Draw the...

2 ( b ) \ begin { tabular } { l } Draw the shear force and bending moment diagrams for the simply supported \ beam as shown in fig. \ \ hline 2 ( c ) \ table [ [ Draw SFD and BMD for a beam ABC 3 . 5...

Dear Tutor, Must find the maximum shear force and bending moment for both Parts. Part A. Beam ABCD is simply supported at B and C and has overhangs at each end (see figure below). The span length is...

Representative Problems 4 . 5 - 1 0 A beam ABC is simply supported at A and B and has an overhang B C ( see figure ) . The beam is loaded by two forces P and a clockwise couple of moment P a at D...

What are share appreciation rights? Why are they advantageous to an employee?

A special instrument package in an experimental aircraft weighs 60 lb. It is supported by three cables, with each cable attached to the end of a cantilever beam. Each beam is equally loaded and is...

EXERCISE 11-14. (Appendix) Calculating Material Variances and Recording Material Costs Quality Cabinet Company uses a standard costing system and produced 2,200 cabinets during May. The standard cost...

35. Ms. Bergen is a loan officer at a trust company. On the basis of her years of experience, she estimates that the probability is 0.025 that an applicant will not be able to repay his or her...

Sketch the normal-stress distribution acting over the cross section at section aa. Neglect the weight of the block. 6 kip -3 in. 12 kip 6 in. D. B.

Determine the normal stress developed at points A and B. Neglect the weight of the block. 6 kip 3 in. 12 kip 6 in.: D. B.

The beveled gear is subjected to the loads shown. Determine the stress components acting on the shaft at point B, and show the results on a volume element located at this point. The shaft has a...

Consider the following sample data: 4 2 5 0 3 2 5 2 3 8 4 8 a . Calculate the range. b . Calculate MAD. ( Round your intermediate calculations to at least 4 decimal places and final answer to 2...

Matsumoto Limited (ML), a large conglomerate firm, has a capital structure that currently consists of 20 percent long-term debt, 10 percent preferred stock, and 70 percent common equity. ML has...

Investing $2,000,000 in TQM's Channel Support Systems initiative will at a minimum increase demand for your products 1.7% in this and in all future rounds. (Refer to the TQM Initiative worksheet in...