Question: A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other

A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±2kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 104 cycles with a factor of safety of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end.

Step by Step Solution

★★★★★

3.48 Rating (164 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

L 06 m F 2 kN n 15 N10 cycles S 770 MPa S 420 MPa Table A20 First evaluate the fatigue stren... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

233-M-E-F-F (51).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A wooden plank is 5.00 m long and supports a 75.0-kg block 2.00 m from one end. If the plank is uniform with mass 30.0 kg, how much force is needed to support each end?

One end of a 0.3 m long steel rod is connected to a wall at 204?C. The other end is connected to a wall which is maintained at 93?C. Air is blown across the rod so that a heat transfer coefficient of...

A stainless steel rod has a square cross section measuring 1 by 1 cm. The rod length is 8 cm, and k = 18 W/m C. The base temperature of the rod is 300C. The rod is exposed to a convection...

HW 3 problems Due 1 0 / 1 6 / 2 0 2 4 It is important to record calculations neatly and completely on engineering paper. 6 - 1 A 1 0 - m m steel drill rod was heat - treated and ground. The measured...

A solid square rod is cantilevered at one end. The rod is 0 . 6 m long and supports a completely reversing transverse load at the other end of + - 2 k N . The material is AISI 1 0 8 0 hot - rolled...

* * PLZ SOLVE AND SHOW ALL WORK AND PROCESS, INCLUDING EXPLANATIONS, THANK YOU!!! * * Problem 6 - 1 3 A solid square rod is cantilevered at one end. The rod is 0 . 6 m long and supports a completely...

Question 2 A solid square rod is cantilevered at one end. The rod is 0 . 6 m long and supports a completely reversing transverse load at the other end of F = + - 2 k N . The material is AISI 1 0 8 0...

A solid square rod is cantilevered at one end. The rod is 0 . 8 m long and supports a completely reversing transverse load at the other end of + - 1 k N . The material is AISI 1 0 4 5 hot - rolled...

A solid square rod is cantilevered at one end. The rod is 0 . 5 m long and supports a completely reversing transverse load at the other end of + - 1 k N . The material is AISI 1 0 8 0 hot - rolled...

A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 1 kN. The material is AISI 1045 hot-rolled steel. If the...

Mario has two close friends: Gianluigi and Rebecca. On the one hand, Gianluigi has just put all his life savings into a restaurant. On the other hand, Rebecca, who hasa regular job, has not done so....

dual has one unit of time which she splits between work and leisure. When she works, her wage rate is 1 per unit of time, and she has no other sources of income.

How much would you pay for a perpetual bond that pays an annual coupon of $ 2 0 0 2 0 0 per year and yields on competing instruments are 1 0 1 0 % ? You would pay $ 2 0 0 0 2 0 0 0 . ( Round your...

Discuss briefly the different control systems with examples.

Describe the effects of different shapes and sizes of metal powders in P/M processing, commenting on the magnitude and significance of the shape factor of the particles?

A ceramic has ko = 0.65 W / m-K. If this ceramic is shaped into a cylinder with a porosity distribution of P = 0.1(x / L) (l - x / L), where x is the distance from one end of the cylinder and L is...

Assume that you are asked to give a quiz to students on the contents of this chapter. Prepare three quantitative problems and three qualitative questions, and supply the answers?

Question 1 (1 point) Marco Chip, Inc. just issued zero-coupon bonds with a par value of $1,000. The bond has a maturity of 28 years and a yield to maturity of 10.15 percent, compounded semi-annually....

Why do stock market investors appear not to be concerned with unique (firm specific) risks when calculating expected rates of return? a)Risk premium for risky assets includes a component to...

You receive a credit card application from Shady Banks Savings and Loan offering an introductory rate of 3.4 percent per year, compounded monthly for the first six months, increasing thereafter to...