A square aluminum bar with pinned ends carries a load P = 25 k acting at distance
Question:
If the stress in the bar is not exceed 6 ksi, what is the minimum permissible width bmin of the bar?
Fantastic news! We've Found the answer you've been seeking!
Step by Step Answer:
Answer rating: 90% (10 reviews)
Pinned ends DATA Units pounds and inches SEC...View the full answer
Answered By
Muhammad Umair
I have done job as Embedded System Engineer for just four months but after it i have decided to open my own lab and to work on projects that i can launch my own product in market. I work on different softwares like Proteus, Mikroc to program Embedded Systems. My basic work is on Embedded Systems. I have skills in Autocad, Proteus, C++, C programming and i love to share these skills to other to enhance my knowledge too.
3.50+
1+ Reviews
10+ Question Solved
Related Book For
Question Posted:
Students also viewed these Mechanics questions
-
A W 8 (28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length Lmax of the column if (a) P = 50 k, and (b) P = 100 k? (Assume E = 29,000 ksi and...
-
A W 250 ( 67 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length Lmax of the column if (a) P = 560 kN, and (b) P = 890 kN? (Assume E = 200 GPa...
-
A circular aluminum tube with pinned ends supports a load P = 18 kN acting at distance e = 50 mm from the center (see figure). The length of the tube is 3.5m and its modulus of elasticity is 73 GPa....
-
Consider the valve failure data in Example 7.6. Set up a one-sided CUSUM chart for monitoring and detecting an increase in failure rate of the valve. Assume that the target value of the mean time...
-
Your company is in a prime vacation spot, and as personnel manager you get many letters from students asking about summer jobs. Company policy is to send everyone an application for employment, a...
-
A particular binary system of two stars in circular orbits is observed to orbit each other about their common center-of- mass that appears to reside at a point midway between them. Explain the logic...
-
Elastically restrained end a. Bending moment \(=0\); shear force equals the b. Deflection \(=0\); slope \(=0\) c. Deflection \(=0\); bending moment \(=0\) d. Bending moment \(=0\); shear force \(=0\)
-
1. What is the basic natural law assumption that guides Steffens discussion of the death penalty? 2. Why does Steffen view the death penalty as an exception and where does Steffen place the burden of...
-
Units produced 18,100 3,620 Direct materials cost per unit $ 7 Machine-hours per unit Production runs per quarter 4 144 $ 19 7 72 Production at the plant is automated and any labor cost is included...
-
A store maintains data on customers, products and purchase records in three tables: CUSTOMER, PRODUCT, PURCHASE. The store manager wants to know which product is on its maximum discount for each...
-
(a) A simple beam AB with length L and height h supports a uniform load of intensity q (see the first part of the figure). Obtain a formula for the curvature shortening λ of this beam....
-
A pinned-end column of length L = 2.1 m is constructed of steel pipe (E = 210 GPa) having inside diameter d1 = 60 mm and outside diameter d2 = 68 mm (see figure.) A compressive load P = 10 kN acts...
-
The table below sets out data for the Mobile Phone Manufacturing Company for the four quarters of Year 1. The fixed overhead production cost for each month is based on budgeted production of 1,000...
-
You have been asked by your boss to select a flow meter to measure the flow rate of gasoline $(\mathrm{SG}=0.85)$ at $70^{\circ} \mathrm{F}$ in a 3 in. sch 40 pipeline. The maximum expected flow rate...
-
Air at $100 \mathrm{psia}$ and $60^{\circ} \mathrm{F}$ is being controlled through a venturi control valve. The backpressure at the valve discharge is $P_{2}=30 \mathrm{psia}$. The flow rate through...
-
A solid particle with a diameter of $5 \mathrm{~mm}$ and an $\mathrm{SG}$ of 1.5 is immersed in a liquid with a viscosity of $10 \mathrm{P}$ and an SG of 1 . How long will it take for the particle to...
-
Calculate the value of the Reynolds number for sodium flowing at a rate of $50 \mathrm{gpm}$ through a tube with a $1 / 2$ in. ID, at $400^{\circ} \mathrm{F}$.
-
Water is pumped upward through a bed of $1 \mathrm{~mm}$ diameter iron oxide particles $(S G=5.3)$. If the bed porosity is 0.45 , over what range of superficial water velocity will the bed be...
-
Determine the moment of inertia of the area about the x axis. 1m - 2 m y = 2x-x
-
Write a declaration for each of the following: a. A line that extends from point (60, 100) to point (30, 90) b. A rectangle that is 20 pixels wide, 100 pixels high, and has its upper-left corner at...
-
A student is asked to measure the acceleration of a cart on a frictionless inclined plane as in Figure 5.11, using an air track, a stopwatch, and a meter stick. The height of the incline is measured...
-
Voyagers 1 and 2 surveyed the surface of Jupiters moon Io and photographed active volcanoes spewing liquid sulfur to heights of 70 km above the surface of this moon. Find the speed with which the...
-
Initially the system of objects shown in Figure P5.61 is held motionless. All surfaces, pulley, and wheels are frictionless. Let the force F is zero and assume that m2 can move only vertically. At...
-
Price, Waterhouse, and Coopers complete their first year of business as a partnership. The partners offer auditing, tax, and advisory services. Use the Tableau Dashboard to determine allocation of...
-
What did economists discover about the American households' retirement saving according to Andrew Biggs' article? Are most American households saving adequately for their retirement, or is there a...
-
Eleanor Inc. creates artisanal crafts for home dcor, the entity has two manufacturing centres: crafting and painting. MOH is allocated based on labour cost in the crafting centre and machine hours in...
Study smarter with the SolutionInn App