Question: At a point on the surface of a machine component the stresses acting on the x face of a stress element are (x = 42

At a point on the surface of a machine component the stresses acting on the x face of a stress element are (x = 42 MPa and Txy = 33 MPa (see figure).
What is the allowable range of values for the stress (y if the maximum shear stress is limited to T0 = 35 MPa?

Try 33 MPa = 42 MPa

Step by Step Solution

★★★★★

3.31 Rating (183 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

s x 42 MPa s y unknown T xy 33 MPa Fin... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

836-P-M-S (648).docx

120 KBs Word File

Students Have Also Explored These Related Mechanics Questions!

At a point on the surface of a machine component, the stresses acting on the x face of a stress element are (x = 5900 psi and Txy = 1950 psi (see figure). What is the allowable range of values for...

At a point on the surface of a machine the material is in biaxial stress with (x = 3600 psi, and (y = - 1600 psi, as shown in the first part of the figure. The second part of the figure shows an...

At each point on the surface of the cube shown in Figure, the electric field is parallel to the z axis. The length of each edge of the cube is 3.0 m. On the top face of the cube E = ?? 34k N/C, and...

6 . 3 - 1 8 At a point on the surface of a machine componat the stresses acting on the x face of a stress element an x = 5 0 MPa and x y = 1 5 MPa ( see figure ) . What is the allowable range of...

2. The stresses shown in the Figure act at a point on the free surface of a machine component. a) Determine the normal stresses x and oy and the shear stress ty at the point. b) Determine the...

The stresses shown act at a point on the free surface of a machine component. The stress magnitudes are S n = 3 0 MPa, S t = 4 5 MPa, and S n t = 1 0 0 MPa, acting in the directions indicated in the...

The following problems are to be solved using Mohr's circle. Neatly and carefully, hand-generate Mohr's circle solutions so that the final solution is easy to identify and grade. Draw Mohr's circles...

The machine component shown below is subjected to a load of P = 1 k N oriented at an angle of = 4 2 . The cross - sectional dimensions of the component are b = 1 6 m m and t = 6 m m . Using x A = 4 0...

Summarize this for me Someone who understand MEA and HEA very well. And please make sure the summary is 2 pages . no less than 2 pages plz thanks Effects of temperature on mechanical properties and...

This text was adapted by The Saylor Foundation under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 License without attribution as requested by the work's original creator or licensee. 1...

Discuss Hart's theory of law with specific reference to the "rule of recognition" and Hart's opinion on "hard cases" .Compare this theory with that of John Austin and Hans Kelsen.

Explain materiality and give an example of both a material and an immaterial item.

Which of the following is true about stocks but not bonds? Stocks have higher expected returns than bonds II . Stocks have steady, known cash flows ( dividends ) that do not change III. Stocks are...

66. Determine the median and the values corresponding to the first and third quartiles in the following data: 5.24 6.02 6.67 7.30 7.59 7.99 8.03 8.35 8.81 9.45 9.61 10.37 10.39 11.86 12.22 12.71...

The shaft is made from a strain-hardening material as shown. If the shaft is subjected to a maximum shear strain of 0.0048 rad, determine the torque applied to the shaft. 2 in.- T

The built-up shaft is designed to rotate at 720 rpm. If the radius at the transition on the shaft is r = 7.5 mm, and the allowable shear stress for the material is allow = 60 MPa, determine the...

The stepped shaft is to be designed to rotate at 600 rpm while transmitting 60 kW of power. Is this possible if the allowable shear stress is allow = 60 MPa and the radius at the transition on the...

Rory works as a financial adviser in a practice with three other advisers. They each own 25% of the business, and while they each look after their own clients, they do share back office, paraplanning...

If a company has both an inflow and outflow of cash related to property, plant, and equipment, the

A consulting aerospace engineer at Aerospatial estimated AW values for a presently owned, highly accurate steel rivet inserter based on company records of similar equipment. A challenger has ESL= 2...