Question: A beam is made up by bolting together two cold-drawn bars of AISI 1018 steel as a lap joint, as shown in the figure. The

A beam is made up by bolting together two cold-drawn bars of AISI 1018 steel as a lap joint, as shown in the figure. The bolts used are ISO 5.8. Ignoring any twisting, determine the factor of safety of the connection

Step by Step Solution

★★★★★

3.39 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

14 kN 350 28 kN R A B 200 50 350 MB 0 0 By symmetry R R 14 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

M-E-S-F (43).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

The cold-drawn AISI 1040 steel bar shown in the figure is subjected to a completely reversed axial load fluctuating between 28 kN in compression to 28 kN in tension. Estimate the fatigue factor of...

The aluminum and steel pipes shown in the figure are fastened to rigid supports at ends A and B and to a rigid plate C at their junction. The aluminum pipe is twice as long as the steel pipe. Two...

The simple beam AB shown in the figure supports two equal concentrated loads P, one acting downward and the other upward. Determine the angle of rotation Î¸A at the left-hand end, the...

( (2) In lecture 1(e), we looked at the problem of minimizing the weight of a cantilever beam subject to the constraint that the deflection should not exceed a certain value. This led to the...

On the imaginary planet of Metalinus, metals have different densities than what they have on Earth. For example, brass has a density of 11 g/cm3 and lead has a density of 15 g/cm3. The beings living...

Before the uniform distributed load is applied on the beam, there is a small gap of 0.2mm between the beam and the post at B . The post at B has a diameter of 40 mm , and the moment of inertia of the...

QUESTION ONE ( 5 0 ) Briefly define the following terms: ( 1 0 ) a ) Ductility ( give one example for the material that behaves in this manner ) b ) Fracture ( give one example for the material that...

A part of a structural system is as shown in the figure below. It consists of a main beam ABCD, pin supported at A and roller supported at C . An extended beam D E is connected to the main beam at D...

Select the lightest " 3 x " beam to support a uniformly distributed load over the whole length of the simply supported beam. The live load is 1 8 0 lb / ft and the dead load is 1 0 0 lb / ft . The...

The Unit - Load Method is a technique used in civil engineering to compute beam deflection. It involves analyzing the deflection caused by a concentrated unit load applied at different positions...

EMPLOYEE SOURCING CASE STUDY Read the case below and answer the all the questions that follow. Increasing Staff to Complete the First Phase Read the Introduction of MRG HPI. MRG HPI Policies and...

Calculating WACC Mullineaux Corporation has a target capital structure of 50 percent common stock, 5 percent preferred stock, and 45 percent debt. Its cost of equity is 15 percent, the cost of...

which of the following are accessible from the money market? A . accounts payable, loan to purchase land and buildings B . bank overdraft:loan repayable within six months c . short - term loan: motor...

Which type of inventory cost includes the interest paid on money borrowed? a) Item cost b) Holding cost c) Capital cost d) Storage cost

Suppose 202 animals are classied into 4 categories as follows: Y = (91:92: 293,314) = (125,18,25,34) The corresponding cell probabilities are known to have the structure 91 62 2(1 61) 1 92 61 ( 3 + 3...

A firm's demand function for product X has the following question: Qx = 1420 -20Px- 10Py + 0.02M + 0.04A where Qx is the quantity purchased, Px is the price of X, Py is the price charged for a...

Huffman Systems has forecasted sales for its new home alarm systems to be 65,000 units per year at $41.00 per unit. The cost to produce each unit is expected to be about 42% of the sales price. The...