Question: Determine the normal force, shear force, and moment at sections passing through points E and F. Member BC is pinned at B and there is

Determine the normal force, shear force, and moment at sections passing through points E and F. Member BC is pinned at B and there is a smooth slot in it at C. The pin at C is fixed to member CD. Units Used: kip = 103 lb Given: M = 350 lb ∙ ft w = 80lb/ft c = 2 ft F = 500 lb d = 3 ft

θ = 60 deg e = 2 ft

a = 2 ft f = 4 ft

b = 1 ft g = 2 ft

W2 (W2 -w)e wi(c) FBC A,

Step by Step Solution

★★★★★

3.49 Rating (175 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

G Mg 0 2d 0 F 0 Fsin0d Cyd e 0 wa F sint Gold 3 d e Fx0 G BxFcos 0 0 By 1 By ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

32-E-C-S (649).docx

120 KBs Word File

Students Have Also Explored These Related Civil Engineering Questions!

Determine the normal force shear force and moment at sections passing through points E and F. member BC is pinned at B and there is a smooth slot in it at C. The pin a C is fixed to memberCD. 500 Ib...

Determine the normal force shear force and moment at a section passing through point D of the two memberframe. 400 N/m 200 N/m 2.5 m 6m-

Determine the normal force. Shear force and moment at a section passing through pointC. Assume the support at A can be approximated by a pin and B as aroller 8 kip 10 kip 0.8 kip'ft -6 ft- -12fA- -12...

the sky hook is used to support the cable of a scaffold over the side of a building. If it consists of a smooth rod that contacts teh parapet of a wall at points A , B , and C , determine the normal...

Questic Not completr Marked out of 2 . 0 0 P Flag question Point B is a connector between members A B and B C that permits rotation. Point E is located to the left of P . Given a = 5 m , b = 4 . 5 m...

Point B is a connector between members A B and B C that permits rotation. Point E is located to the left of P . Given a = 5 . 1 m , b = 4 . 8 m , W = 1 . 4 N m , and P = 2 . 6 N , determine the...

Determine the shear force and moment at section passing through point E . Member B C is pinned at B and there is a smooth slot in it at C . The pin at C is fixed to member CD . V E = - 2 5 0 l b and...

Determine the internal normal force, shear force, and moment acting at sections passing through points B and C on the curvedrod. 13 2 ft 45 30 4(X) Ib 300 Ib

Determine the internal normal force, shear force, and moment at points D and E of the frame which supports the 200-lb crate. Neglect the size of the smooth peg at C. 4.5 It 4 ft 211 1.5 It 1.5 ft

A truss is loaded and supported by a pin at E and a roller at A . The truss is shown in the figure. All the internal points are pinned. Using the method of joints and / or the method of sections,...

CP7-1 (Perpetual Method) Jeter Co. uses a perpetual inventory system and both an accounts receciv- able and an accounts payable subsidiary ledger. Balances related to both the general ledger and the...

Suppose that you are a monopolist who produces gizmos, Z, with the total cost function C(Z) = F + 50Z, where F represents the firm's fixed cost. Your marginal cost is MC = 50. Suppose also that there...

3. Slowdown in Labor Productivity Growth What slowed the rate of growth in labor productivity during the 19731982 period?

Determine the total estimated cost at completion and estimated cost to complete for the project in Problem 6, assuming the cost performance index remains the same through the remainder of the job. In...

Determine the present value of $400,000 to be received in three years, using an interest rate of 10%, compounded annually, as follows: (a) By successive divisions. (Round to the nearest dollar.) (b)...

Using a present value table, your calculator, or a computer program present value function, answer the following questions: Required: a. What is the present value of nine annual cash payments of...

On July 1, 2014, Livingston Corporation, a wholesaler of manufacturing equipment, issued $46,000,000 of 20-year, 10% bonds at a market (effective) interest rate of 11%, receiving cash of $42,309,236....

Ethical Dilemma The American car battery industry boasts that its recycling rate now exceeds 95%, the highest rate for any commodity. However, with changes brought about by specialization and...

Can you think of ways that globalization has helped you economically? Can you think of ways that it has not?

Determine the force F at the end of the beam C so that the displacement at C is zero. EI is constant. Use the conjugate-beam method. B

Determine the force F at the end of the beam C so that the displacement at C is zero. EI is constant. Use the moment-area theorems. B-

Determine the displacement at C and the slope at B. EI is constant. Use the conjugate-beam method. fot JA

You own a portfolio equally invested in a risk-free asset and two stocks. If one of the stocks has a beta of 1.32 and the total portfolio is equally as risky as the market, what must the beta be for...

Show by resolution that B follows from S where S = {A & B, C}

PERSONAL FINANCE PROJECT Answer the following questions. Critically think through your answers with the knowledge that you have learned in this class. You can refer back to the textbook. Keep in mind...