Determine the normal reaction at the roller A and horizontal and vertical components at pin B for

Question:

Determine the normal reaction at the roller A and horizontal and vertical components at pin B for equilibrium of the member.

Units Used:

kN = 103 N

Given:

F1 = 10kN

F2 = 6kN

a = 0.6 m

b = 0.6 m

c = 0.8 m

d = 0.4 m

θ = 60 deg

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Engineering Mechanics Statics

ISBN: 978-0132215008

11 Edition

Authors: Russell C. Hibbeler

See More Books

Question Posted: Jun 10, 2010 12:32 AM

See More Questions

Determine the horizontal and vertical components of reaction at pin C and the force in the pawl of the winch in Prob. 510.
Determine the horizontal and vertical components of reaction at the pin supports A and E of the compound beamassembly. 2 kip/ft 2t 1 ft 3ft -2 ft- 6 It-
Determine the horizontal and vertical components of reaction at the pin A and the normal force at the smooth peg B on themember. 0.4 m J30 0.4 m F= 600 N 30
If the end of the cord is pulled downward with speed v C , determine the angular velocities of pulleys A and B and the speed of block D. Assume that the cord does not slip on the pulleys. Given: VC =...
Refer to the Environmental Science & Technology (Jan. 2005) investigation of MTBE contamination in 70 New Hampshire groundwater wells, Exercise 14.33 (p. 14-22). Recall that the level of MTBE...
Capital balances in Pelmar Co. are Lango $40,000, Oslo $30,000, and Fernetti $20,000. Lango and Oslo each agree to pay Fernetti $12,000 from their personal assets. Lango and Oslo each receive 50% of...
Platinum Status Ltd uses an annual flexible budget based on standard direct machine hours for the following factory overhead items. Required (a) Why is a flexible budget performance report a better...
The accounting records of Ortiz Manufacturing Company (OMC) revealed that the company incurred $3 million of materials, $5 million of production labor, $4 million of manufacturing overhead, and $6...
How can chemical engineering principles be applied to optimize the production of biofuels from lignocellulosic biomass? Consider the various pretreatment methods, enzymatic hydrolysis, and...
Is there evidence consistent with gender discrimination in training level? To answer this, proceed as follows: a. Create a table of counts for the two qualitative variables gender and training level....
If the maximum intensity of the distributed load acting on the beam is w, determine the reactions at the pin A and roller B. Units Used: kN = 103 N Given: F = 6 kN a = 3 m b = 3 m w = 4 kN/m b. a.
The symmetrical shelf is subjected to uniform pressure P. Support is provided by a bolt (or pin) located at each end A and A' and by the symmetrical brace arms, which bear against the smooth wall on...
In Exercises use the properties of summation and Theorem 4.2 to evaluate the sum. Use the summation capabilities of a graphing utility to verify your result. Data from in Theorem 4.2 24 i=1 4i
Import Transaction Details: S & S Co. imported 3200 pairs of Cross-Country Skis into Canada. The Skis were packaged into 3200 boxes (1 pair of Skis per box; box #1 to box #3200). Each Ski is valued...
Three students are pulling on ropes attached to a ring as shown in the figure below. Determine the magnitude and direction of the net force. Enter the direction as an angle measured in degrees...
Ava Miller has just completed the second year of operating her veterinary clinic. You have been retained by Ava for tax assistance and advice. At a recent meeting, you gathered information on her...
How can organizations establish and maintain a culture of continuous learning and knowledge sharing to facilitate employee development and organizational resilience in the face of rapid technological...
Suppose that a lemonade stand's lemonade recipe consists of 2 cups of sugar, 3 cups of lemon juice, and 5 cups of water per batch. a) How much sugar and water should be added if they only use 1 cup...
Mandalay Industries is considering a new project with a 4-year life with the following cost and revenue data. This project will require an investment of $$145,000$ in new equipment. This new...
Create an appropriate display of the navel data collected in Exercise 25 of Section 3.1. Discuss any special properties of this distribution. Exercise 25 The navel ratio is defined to be a persons...
NML plc is considering buying a new machine costing 200,000 which would generate the following before-tax cash flows from the sale of goods produced. NML pays corporation tax of 19 per cent per year...
Determine the moments at the supports A and C, then draw the moment diagram. Assume joint B is a roller. EI is constant. 25 kN 15 kN/m A. - 4 m- - 3 m -3 m-
Determine the moments at A, B, and C, then draw the moment diagram for the beam. The moment of inertia of each span is indicated in the figure. Assume the support at B is a roller and A and C are...
Determine the moments at A, B, and C and then draw the moment diagram. EI is constant. Assume the support at B is a roller and A and C are fixed. 3 k 3k B. |- 3 ft--3 ft -3 ft -- -10 ft- 10 ft
Large-scale industrial production - accompanied by massive technological change, expanding international communication networks, and pro-growth government policies-generated rapid economic...
How can this relate to individuals who have had a TBI and are currently homeless or marginally housed?
1. According to Marxian theory, are crises an economic process inherent to the accumulation dynamics of current capitalism? Justify your answer. 2. According to Marxian theory, what do you consider...

Determine the normal reaction at the roller A and horizontal and vertical components at pin B for

Question:

Step by Step Answer:

Initial Guesses N 1 kN Bx 1 kN By 1 ...View the full answer

Engineering Mechanics Statics

Students also viewed these Civil Engineering questions