Question: Explain why a 0.2% offset is used to determine the yield strength in a tension test.

Explain why a 0.2% offset is used to determine the yield strength in a tension test.

Step by Step Solution

★★★★★

3.36 Rating (165 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

In hardness test if the indenter is worn out and blunt then under a given value of load the ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Document Format (1 attachment)

Word file Icon

972-E-M-E-B-D (246).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

Explain how tandem mass spectroscopy is used to determine the sequence of a peptide. Once a peptide sequence is known, how is this information used to determine the sequence of the entire protein?

Q:

Explain how the Doppler effect with microwaves is used to determine the speed of an automobile.

Q:

A Pitot tube (Figure) is used to determine the airspeed of an airplane. It consists of an outer tube with a number of small holes B (four are shown) that allow air into the tube; that tube is...

Q:

Summarize this for me. Someone who understand the HEA and MEA perfectly and also the summary should be 2 or over 2 pages. Someone who understands this perfectly A scrap-tolerant alloying concept...

Q:

MAT 33 - Fall 2016 Homework #6 Due: 10/24/2016 1.) A cylindrical specimen of some metal alloy 12mm in diameter is stressed elastically in tension. A force of 26,500N produces a reduction in specimen...

Q:

Q1. The stress-strain diagram for a bone is shown, and can be described by the equation 0.45 (106) + 0.36 (1012), where is in kPa. Determine the yield strength assuming a 0.2% offset Hint: calculate...

Q:

A bar with a rectangular cross section that has a width of 2 4 . 5 mm , a thickness of 6 . 1 mm and a gauge length of 7 5 mm was tested in tension to fracture. Use the load - elongation...

Q:

A specimen of magnesium having a rectangular cross section of dimensions 3.2 mm x 19.1 mm is deformed in tension. Using the given load-elongation data answer the questions below. a) Plot the data as...

Q:

Question 1 (8 points) A cylindrical specimen of aluminum having a diameter of 0.543in.(13.8mm) and a gauge length of 2.07in.(52.6mm) is pulled in tension. Use the following engineering stress-strain...

Q:

A tensile test is conducted on a rectangular cross - section steel alloy bar with dimensions 6 . 2 5 mm x 3 7 . 5 mm and a initial length of 2 0 3 mm . The results obtained from the experiment are...

Q:

Is it likely that SKI could make significantly greater use of accruals? Dan Barnes, financial manager of Ski Equipment Inc. (SKI), is excited but apprehensive. The companys founder recently sold his...

Q:

1. Using relevant examples discuss the five most important variables that may cause the market for demand curve for labor to shift 2. Why do you think our economy continues to experience wage...

Q:

Assume that the interest rate is such that the project breaks even. Should the project be undertaken if the interest rate rises? Explain.

Q:

What is the real exchange rate and how does it affect output and trade?

Q:

Repeat Prob. 377 with the chain parallel to the z axis with P in the positive z direction. Repeat Prob. 377, A torque T = 100 N · m is applied to the shaft EFG, which is running at constant...

Q:

Repeat Prob. 377 with T = 900 lbf · in, a = 6 in, b = 5 in, c = 10 in, d = 1.375 in, e = 4 in, f = 10 in, and g = 6 in. Repeat Prob. 377, A torque T = 100 N · m is applied to the shaft...

Q:

The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy = 200 lbf and Fx = Fz = 0. Analyze the stress situation in rod AB by obtaining the following...

Q:

ShowthatthefunctionbelowisthePDFofR,thedistance betweentheepicenterofan earthquake and the site of a dam, when the epicenter is equally likely to be at any location along a neighboring fault (see...

Q:

Integrative-Leverage and risk Firm has sales of 104.000 units at $2.05 per unit, variable operating costs of $1.71 per unit, and fixed operating costs of $6,000 Interest is $10.080 per year Firm Whas...

Q:

The greatest competitive advantage in managing employees in a customer-strategy organization lies in: Using technology to automate more routine jobs. Equalizing salaries to value lower-tier...