Question: For Prob. 945, determine the weld size if the maximum allowable shear stress is 20 kpsi. Prob. 945, A 2-in dia. steel bar is subjected

For Prob. 9–45, determine the weld size if the maximum allowable shear stress is 20 kpsi.

Prob. 9–45, A 2-in dia. steel bar is subjected to the loading indicated. Locate and estimate the maximum shear stress in the weld throat.


For Prob. 9–45, determine the weld size if the maximum


F T____
2 ......kips 15 kip ·in

6 in in 2-in dia.

Step by Step Solution

★★★★★

3.54 Rating (178 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

F 2 kip T 15 kipin Bending Table 9... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Document Format (1 attachment)

Word file Icon

233-M-E-W-B (129).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Q:

A cylindrical 4340 steel bar is subjected to reversed rotating-bending stress cycling, which yielded the test results presented in Figure 8.20. If the maximum applied load is 5,000 N, compute the...

Q:

A 2-in dia. steel bar is subjected to the loading indicated. Locate and estimate the maximum shear stress in the weld throat. F T____ 2 ...... kips 15 kip ·in 6 in in 2-in dia.

Q:

A 2-in dia. steel bar is subjected to the loading indicated. Locate and estimate the maximum shear stress in the weld throat. F T____ 2 ...... kips0 6 in in 2-in dia.

Q:

A 2 - in . diameter steel bar is subjected to the loading indicated. Locate and estimate the maximum shear stress in the weld throat. F = 3 kips , T = 1 5 kip.in . , and h = 0 . 2 5 in . Determine...

Q:

a) for a small effect size, 0.20 in G'Power 3.1.9.7 X b.) for a medium effect size, 0.50 File Edit View Tests Calculator Help Central and noncentral distributions Protocol of power analyses critical...

Q:

5 . 5 . 8 Considering the rainfall - runoff data in Prob. 5 . 3 . 1 and using the curve number determined in Prob. 5 . 5 . 7 , determine the cumulative infiltration and the cumulative rainfall excess...

Q:

For the bar of Prob. 2/135, determine the values of r and if the velocity of collar C is decreasing at a rate of 5 mm/s 2 at the instant in question. Refer to the printed answers for Prob. 2/135 as...

Q:

Prob. 1 A factored logic expression is given as (AB + C) D (E+F). 1.1) How many AND/OR gates are needed to implement the factored f(A,B,C,D,E,F)? A. 4 B. 5 C. 3 D. None of the above 1.2) How many...

Q:

flud for the threc - dimensional case. 2 . 2 . The container of Fig. 2 . 4 4 holds water and air as shown. What is the pressure at A , B , C , and D in pounds per square foot? 2 . 3 . The tube in...

Q:

1 - 8 3 . Determine the required minimum thickness t of member A B and edge distance b of the frame if P = 4 0 k N and the factor of safety against failure is 2 . The wood has a normal failure stress...

Q:

Kate has the following income and outgoings for 2018/19: Trading profit 38,000 Employment Income 8,000 Bank Deposit Interest (amount received) 3,500 Dividend income (amount received) 7,000 PAYE of...

Q:

A capacitor's plates hold 1.3 C when charged to 60 V. What's its capacitance?

Q:

The wide gap between stock market returns and the return on treasury bills is known as the and the view that the difference between the two is abnormally high is known as the

Q:

Discuss the critical components of job design in detail.

Q:

A punch-press geared 10:1 is to make six punches per minute under circumstances where the torque on the crankshaft is 1300 lbf ?ft for s. The motors nameplate reads 3 bhp at 1125 rev/min for...

Q:

The punch-press of Prob. 1629 needs a flywheel for service on the crankshaft of the punch press. Design a satisfactory flywheel to the extent of specifying material, rim inside and outside diameters,...

Q:

Compare the designs resulting from the tasks assigned in Probs. 1629 and 1630. What have you learned? What recommendations do you have?

Q:

YTM= 8.57% RISK FREE RATE = 1.3% BETA = 3.13 Ch 14: Using the Risk Free rate from above, and assuming a 4 percent market risk premium a) What is the cost of equity for your selected company using...

Q:

Suppose we have the following returns for large-company stocks and Treasury bills over a six year period: Year Large Company US Treasury Bill 1 3.96 4.50 2 14.12 4.88 3 19.01 3.80 4 14.67 6.96 5...

Q:

The Stata data file (elemapi.dta) contains data on 21 school-related variables in 400 U.S. schools. Please refer to the text file (elemapi description.txt) for a description of these variables. (a)...