Hot combustion gases (air) at 1500 K is used as heat source in a heat engine where

Question:

Hot combustion gases (air) at 1500 K is used as heat source in a heat engine where the gas is cooled to 750 K and the ambient is at 300 K. This is not a constant T source. How does that affect the efficiency?

Fantastic news! We've Found the answer you've been seeking!

Step by Step Answer:

Related Book For book-img-for-question

Fundamentals of Thermodynamics

ISBN: 978-0471152323

6th edition

Authors: Richard E. Sonntag, Claus Borgnakke, Gordon J. Van Wylen

See More Books

Question Posted: Feb 23, 2016 06:55 AM

See More Questions

Hot combustion gases (air) at 1500 K is, used as heat source in a heat engine where the gas is cooled to 750 K and the ambient is at 300 K. This is not a constant T source. How does that affect the...
Hot exhaust gases leaving an internal combustion engine at 4008C and 150 kPa at a rate of 0.8 kg/s is to be used to produce saturated steam at 2008C in an insulated heat exchanger. Water enters the...
Hot combustion air at 1500 K expands in a polytropic process to a volume 6 times as large with n = 1.5. Find the specific boundary work and the specific heat transfer.
Explain factors governing recruitment?
Describe the procedure used to stop payment on a check. Why might you wish to initiate this process?
The diagram shows an isosceles triangle PQR inscribed in a circle, centre O, radius r cm. PR = QR and angle ORP = radians. Triangle PQR has an area of A cm 2 . a. Show that A = r 2 sin 2 + r 2 sin 2...
How many ways can a company select 4 candidates to interview from a short list of 12 engineers?
The chairman of the board of Hughes Corporation proposed that the board hire as controller a CPA who had been the manager of the team that conducted Hughes Corporations audit engagement. The chairman...
The Smith family is moving to Little Rock because of a job relocation. They decide to purchase a home near Ms. Smith's office which is in a part of town that was established in the mid-1980's. When...
Given a Q-point of IDQ = 3 mA and VGS = -3 V, determine IDSS if VP = -6 V.
A large stationary diesel engine produces 15 MW with a thermal efficiency of 40%. The exhaust gas, which we assume is air, flows out at 800 K and the intake is 290 K. How large a mass flow rate is...
A remote location without electricity operates a refrigerator with a bottle of propane feeding a burner to create hot gases. Sketch the setup in terms of cyclic devices and give a relation for the...
Write the differential equations defining (a) The displacements of the mass m and of the point A, (b) The charges on the capacitors of the electrical analogue. V ind
Rank from fastest to slowest the following waves according to their speed of propagation: A. An earthquake wave B. A tsunami C. A sound wave in air D. A light wave
A microscope with an 8.0 -mm-focal-length objective has a tube length of \(16.0 \mathrm{~cm}\). For the microscope to be in focus, how far should the objective lens be from the specimen?
The highest magnetic fields in the world are generated when large arrays, or "banks," of capacitors are discharged through the copper coils of an electromagnet. At the National High Magnetic Field...
A physician is using Doppler ultrasound to measure the motion of a patient's heart. The device measures the beat frequency between the emitted and the reflected waves. Increasing the frequency of the...
A parallel-plate capacitor consists of two plates, each with an area of \(28 \mathrm{~cm}^{2}\), separated by \(3.0 \mathrm{~mm}\). The charge on the capacitor is \(8.3 \mathrm{nC}\). A proton is...
In Exercises find the length of the curve over the given interval. Polar Equation r = 5 cos 0 Interval = 0 7/7 0= 2
Solve each problem. Find the coordinates of the points of intersection of the line y = 2 and the circle with center at (4, 5) and radius 4.
A 0.04-m3 open pan of water at 20C is sitting on the burner of a stove. How much heat is needed to completely vaporize the water?
A vertical frictionless piston-cylinder device contains 50 kg of steam at 200 kPa and 300C. Determine the heat transfer and the work done during the process if the steam is cooled at constant...
A frictionless piston maintains a constant pressure of 120 kPa as 0.6 kg of air is being heated in a cylinder. Estimate the work and the heat transfer required if the initial temperature of the air...
Compare and contrast strategic leadership against other leadership models including situations that call for strategic leadership versus other models of leadership and why.
Describe the role of Leadership in healthcare. Describe the role of Strategic Leadership in healthcare. Describe the difference between Leadership and Strategic Leadership in healthcare.
What is a good Annotated Bibliography for the following three books? Re-Thinking Strategic Leadership in the Digital Age by Sabine Dembkowski Exploring the Concept of Strategic Leadership by...

Hot combustion gases (air) at 1500 K is used as heat source in a heat engine where

Question:

Step by Step Answer:

If the efficiency is writt...View the full answer

Fundamentals of Thermodynamics

Students also viewed these Thermodynamics questions