Question: How many strokes per minute would be required to obtain a cutting speed of 36.6 m (120 ft) per minute on a typical mechanical-drive shaper

How many strokes per minute would be required to obtain a cutting speed of 36.6 m (120 ft) per minute on a typical mechanical-drive shaper if a 254-mm (10-in.) stroke is used?

Step by Step Solution

★★★★★

3.38 Rating (167 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

For Rs 220360 0611 Ns 12120061 ... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

916-E-M-S-E-M-S (1755).docx

120 KBs Word File

Students Have Also Explored These Related Materials Science Engineering Questions!

The rotor of a six-pole synchronous generator is rotating at a mechanical speed of 1200 r/min. a. Express this mechanical speed in radians per second. b. What is the frequency of the generated...

How much time would be required to shape a flat surface 254 mm (10 in.) wide and 203 mm (8 in.) long on a hydraulic drive shaper, using a cutting speed of 45.7 m (150 ft) per minute, a feed of 0.51...

How much pressure would be required to compress a quantity of mercury by 0.010%?

Q3. How many strokes per minute would be required to obtain a cutting speed of 45m/min on a typical mechanical drive shaper if a 286-mm stroke is used? The return to cutting time ratio is 4:8, and...

uantitative Analysis BA 452 Homework 3 Questions Homework 3 covers the theory and applications in Lessons I-6 and I-7. This document has four parts: Objectives of doing your homework. Assignment of...

Analyze the case International Cosmetics Limited and answer the question given at the end (25 marks) International Cosmetics Limited Mr. Himendra Ratnayake, factory manager at International Cosmetics...

International Cosmetics Limited Mr. Himendra Ratnayake, factory manager at International Cosmetics Limited (ICL) in Ja-Ela near Colombo, Srilanka was concerned about the quantity & quality of output...

\fprocess a batch of material from the kneader. The output from the extruder was fed continuously into a stamping machine, where a set of 7 dies stamped out wet double coils each weighing 45 grams....

18. A positive displacement pump's speed can be regulated between 12 and 44 strokes per minute. At 21 strokes per minute the pump delivers 40 gallons per minute. What does the pump deliver at 12 and...

Addition of HBr to a double bond with an ether (?OR) substituent occurs region specifically to give a product in which the ?Br and ?OR are bonded to the same carbon. Draw the two possible carbocation...

Select 3 organizations from the list below: TRUSTe Verisign Consumer League Amazon Apple Use a search engine to search for the websites and complete the following steps: Open each website in a...

ur firm owns some equipment that it purchased four years ago at a cost of $ 2 8 7 , 0 0 0 . The equipment is five - year property for MACRS. The MACRS rates are . 2 , . 3 2 , . 1 9 2 , . 1 1 5 2 , ....

Find the solutions (roots) of 6x2 x 2 = 0. a) 2, 3 b) 1/2, 1/3 c) 1/2, 2/3 d) 2/3, 3 e) 2, 1/3

A piece of experimental apparatus is located where g = 9.5 m/s2 and the temperature is 5C. An air flow inside the apparatus is determined by measuring the pressure drop across an orifice with a...

Two piston/cylinder arrangements, A and B, have their gas chambers connected by a pipe. Cross-sectional areas are AA = 75 cm2 and AB = 25 cm2 with the piston mass in A being mA = 25 kg. Outside...

Two hydraulic piston/cylinders are of same size and setup as in Problem 2.73, but with negligible piston masses. A single point force of 250 N presses down on piston A. Find the needed extra force on...

Cavo Corporation expects an EBIT of $19,750 every year forever. The company currently has no debt, and its cost of equity is 15 percent. The corporate tax rate is 35 percent. a. What is the current...

Mickleson Golf Industries sells custom golf clubs and has an all-cash sales policy. They currently sell 1,200 clubs a month for $155 each. The variable costs per club are $125. They are analyzing...

2. Caterpillar (CAT), a US multinational, wants to borrow 150 million Canadian dollars at a fixed rate of interest for five years. Algoma Steel, a Canadian integrated steel manufacturer, wants to...