Question: In Figure 10-F, the angle 9 on the part needs to be inspected. The setup used is shown in Figure 10-G. (No sine plate was

In Figure 10-F, the angle 9 on the part needs to be inspected. The setup used is shown in Figure 10-G. (No sine plate was available.) Determine the angle 6 from the part drawing and the valve of X for the stack of gage blocks.

1.125 +0.0001 -0,0002 500 +0.0002 +0.0000 2.000 -0.0002 FIGURE 10-F

Step by Step Solution

★★★★★

3.38 Rating (148 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

The probe is used to find the stack of gage blocks that exact... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

916-E-M-S-E-M-S (1153).docx

120 KBs Word File

Students Have Also Explored These Related Materials Science Engineering Questions!

The centre-of-mass differential cross-section for the reaction e + e Î¼ + Î¼ due to the one-photon exchange diagram in Figure 10.2(a) is given in Equation (7.15), where s =...

In Figure, a light ray in air is incident at angle ?1 on a block of transparent plastic with an index of refraction of 1.56. The dimensions indicated are H = 2.00 cm and W = 3.00 cm. The light passes...

In Figure force F is applied to a crate of mass m on a floor where the coefficient of static friction between crate and floor is ?s. Angle ? is initially 0o but is gradually increased so that the...

Find attached Ingredients: Water, MCC, Salt, Nicotine, pH regulator, sweeteners and flavours I am wondering why the decision to go with LYFT. I understand migrating to LYFT would be easier from sells...

Please help me answer Part 1 and Part 3 - Current Loop SF42 ( length 8.4 cm ) Experiment 1 - Part 1 in Answer Sheet Experiment 4 - Part 3 in Answer Sheet Experiment 4 - Part 3 in Answer Sheet Current...

i need al the work and lab simulations and pre labs and calculations. LAB SIMULATIONS MUST BE ON PROTEUS ISIS INTRODUCTION: Linear circuit elements resistors, capacitors, and inductors are the...

I've provided all the information, I would appreciate assistance with Question 5 and 6 as well as Graph 1 and 2 and Data Table 3 and 4. Thank you. Exercise 1 Measuring Static and Kinetic Friction In...

can i get a solution to this question please. Value: Document (include your file name) 15% of final grade How to complete: 1. Read the following Anniversary Party scheduling problem: As the project...

Purpose To understand more about vectors, by using three completely different methods of vector addition. We will use the data collected by a group of students to complete this work. The instruction...

Experimental Data is R= 200arbs 5 arbs theta= 223 5 Purpose To understand more about vectors, by using three completely different methods of vector addition. We will use the data collected by a group...

Pepsi-Cola was incorporated in Delaware in 1919 and reincorporated in North Carolina in 1986. PepsiCos product portfolio includes a wide range of foods and beverages, including many iconic brands...

Write a paper identifying, describing, and assessing consumer behavior theory models. Examine, analyze, and reflect how Consumer Behavior contributes to and influences.

3. If GDP is confidently expected to grow at a rapid 4% rate this year, how do you predict investment spending to change? Is it likely to grow at a larger, smaller, or the same rate as GDP? Why?

Point out differences between internal and international trade.

A hydraulically operated multidisk plate clutch has an effective disk outer diameter of 6.5 in and an inner diameter of 4 in. The coefficient of friction is 0.24, and the limiting pressure is 120...

Look again at Prob. 1617. (a) Show how the optimal diameter d is related to the outside diameter D. (b) What is the optimal inner diameter? (c) What does the tabulation show about maxima? (d) Common...

A cone clutch has D = 330 mm, d = 306 mm, a cone length of 60 mm, and a coefficient of friction of 0.26. A torque of 200 N ?m is to be transmitted. For this requirement, estimate the actuating force...

Required information Skip to question [The following information applies to the questions displayed below.] A pension fund manager is considering three mutual funds. The first is a stock fund, the...

A firm offers terms of 2.6/7, net 30. a. What effective annual interest rate does the firm earn when a customer does not take the discount? (Use 365 days a year. Do not round intermediate...

Balance Sheet Current assets Cash 1,010,000 Acc receivable not given Inventories 1,150,000 Fixed assets 4,100,000 TOTAL ASSETS 7, 200,000 Current liabilities Acc payable not given Long-term debt...