Question: Reconsider Prob. 7-124. Using EES (or other) software, redo the problem by including the effects of the kinetic energy of the flow by assuming an

Reconsider Prob. 7-124. Using EES (or other) software, redo the problem by including the effects of the kinetic energy of the flow by assuming an inlet-to-exit area ratio of 1.5 for the compressor when the compressor exit pipe inside diameter is 2 cm.
Prob. 7-124
Refrigerant-134a enters an adiabatic compressor as saturated vapor at 100 kPa at a rate of 0.7 m3/min and exits at 1-MPa pressure. If the isentropic efficiency of the compressor is 87 percent, determine
(a) The temperature of the refrigerant at the exit of the compressor and
(b) The power input, in kW. Also, show the process on a T-s diagram with respect to saturation lines.

I MPa R-134a Compressor 100 kPa sat. vapor

Step by Step Solution

★★★★★

3.40 Rating (159 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Problem 7124 is reconsidered The problem is to be solved by considering the kinetic energy and by assuming an inlettoexit area ratio of 15 for the com... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

837-ME-T (5259).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

Reconsider Prob. 7109. Using EES (or other) software, redo the problem by including the effects of the kinetic energy of the flow by assuming an inlet to-exit area ratio of 1.5 for the compressor...

Reconsider Prob. 9-83. Using EES (or other) software, allow the mass flow rate, pressure ratio, turbine inlet temperature, and the isentropic efficiencies of the turbine and compressor to vary....

Reconsider Prob. 2-59E. Using EES (or other) software, study the effects of the unit cost of energy, the new combustion efficiency on the annual energy, and cost savings. Let the efficiency vary from...

5-43C Consider an adiabatic turbine operating steadily. Does the work output of the turbine have to be equal to the decrease in the energy of the steam flowing through it? 5-44C Consider an air...

5-180 Determine the power input for a compressor that compresses helium from 150 kPa and 20C to 400 kPa and 200C. Helium enters this compressor through a 0.1-m2 pipe at a velocity of 15 m/s. 5-181...

Please quality check my solutions for this advanced heat transfer problem. Show all work. Thank you. All original documents are located at the bottom. 3.9 COMPACT HEAT EXCHANGERS 3.9.10-1 3.9.10...

my question: The related case is put below with images. Can you describe trivago's organization design since 2010 by considering its structural dimensions such as formalization, specialization,...

BLC Inc. is a medium-sized manufacturing company based in the UK. The company operates mainly in the London area and is based in Peterborough. At a recent board meeting, the company decided to expand...

Attached is Accounting assignment along side recommended readings to answer certain questions. Thank you Assignment 1 Problem 1 15 points Reading - W. L. Ferrara, Cost/Management Accounting: The 21st...

In the Intro to Purchasing and Supply Chain reading, Page 6, Figure 1-2, there is a comparison of Traditional Purchasing versus the Current Outlook. Provide three reasons why the Current Outlook is...

A manufacturer produces two products A and B. Both the products are processed on two different machines. The available capacity of first machine is 12 hours and that of second machine is 9 hours per...

General Audit Planning Information: Materiality=$40,000 PAJE Scope = $2,000 Audit Findings: 1. When auditing prepaid expenses, it was discovered that the prepaid insurance account was overstated by...

Does our creative approach match our positioning strategy?

You have a consultancy contract to provide advice to a medium-sized specialist engineering company that supplies equipment to the energy generation business. The business is efficiently run but is...

A torsion-bar spring consists of a prismatic bar, usually of round cross section, that is twisted at one end and held fast at the other to form a stiff spring. An engineer needs a stiffer one than...

An engineer is forced by geometric considerations to apply the torque on the spring of Prob. 43 at the location x = 0.2l. For a uniform-diameter spring, this would cause the long leg of the span to...

A bar in tension has a circular cross section and includes a conical portion of length l , as Shown, the task is to find the spring rate of the entire bar. Equation (44) is useful for the outer...

Capital Budgeting Methods Project S has a cost of $10,000 and is expected to produce benefits (cash flows) of $3,000 per year for 5 years. Project L costs $25,000 and is expected to produce cash...

Rafael is an analyst at a wealth management firm. One of his clients holds a $10,000 portfolio that consists of four stocks. The investment allocation in the portfolio along with the contribution of...

You plan to invest in the Kish Hedge Fund, which has total capital of $500 million invested in five stocks: Stock Investment Stock's Beta Coefficient $160 million 0.3 120 million 80 million 1.7 80...