Question: A speed reducer has 20 full-depth teeth and consists of a 22-tooth steel spur pinion driving a 60-tooth cast-iron gear. The horsepower transmitted is 15

A speed reducer has 20◦ full-depth teeth and consists of a 22-tooth steel spur pinion driving a 60-tooth cast-iron gear. The horsepower transmitted is 15 at a pinion speed of 1200 rev/min. For a diametral pitch of 6 teeth/in and a face width of 2 in, find the contact stress.

Step by Step Solution

★★★★★

3.58 Rating (159 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

Eq 144b dp Eq 1414 V K W 22 3667 1200 12 1200 1152 1200 63 02515 120036672 366... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Document Format (1 attachment)

M-E-S-G (11).docx

120 KBs Word File

Students Have Also Explored These Related Mechanical Engineering Questions!

A steel spur pinion and gear have a diametral pitch of 12 teeth/in, milled teeth, 17 and 30 teeth, respectively, a 20 pressure angle, and a pinion speed of 525 rev/min. The tooth properties are Sut =...

A steel spur pinion has a pitch of 6 teeth/in, 22 full-depth teeth, and a 20 pressure angle. The pinion runs at a speed of 1200 rev/min and transmits 15 hp to a 60-tooth gear. If the face width is 2...

A steel spur pinion has a diametral pitch of 12 teeth/in, 16 teeth cut full-depth with a 20 pressure angle, and a face width of in. This pinion is expected to transmit 1.5 hp at a speed of 700...

A speed reducer has 2 0 full depth teeth

Motor 15cm Shaft 2 Pulley t V belt driver Gear B Pulley F Shaft #1 L Table 1: Gears & Pulleys diameter Son Gear H Gear A Shaft s Shaft #3 Gear C Chain driver Gear D Shaft #4 Figure 1: Schematic of...

In this project, the objective is to create a speed reduction system, which is utilized to decrease rotational speed while enhancing output torque. Speed reducers find applications across various...

please do it 4 hour will upvote A speed reducer is to be designed for a Power Transmission System used in a small equipment. According to the lay-out given below, the pulley M is the driver pulley...

In this project, the objective is to create a speed reduction system, which is utilized to decrease rotational speed while enhancing output torque. Speed reducers find applications across various...

1 - Eccentric speed reducer The figure below shows a schematic representation of an eccentric speed reducer along with a kinematic model. The input member is D (carrier) which carries 2 planets B and...

Background Many industrial applications require machinery to be powered by engines or electric motors. The power source usually runs most efficiently at a narrow range of rotational speed. When the...

How should the sample size be determined for the survey of question 9?

Laurie Siegel, senior vice president of human resources for Tyco International took over her job in 2003, just after numerous charges forced the companys previous board of directors and top...

Queman Moster Mily: "Mitemalp, Murum IRS Herverta 5 7 = buin 1 9 of 3 0 Concepts computed Multiple Choice Question Which of the following is true regarding the balance sheet components? Liabilities...

Hydrogen can cause fire hazards, and hydrogen gas leaking into surrounding air can lead to spontaneous ignition with extremely hot flames. Even at very low leakage rate, hydrogen can sustain...

write a function that determines the power transmitted to the load (p), the ratio of short circuit current (io) and the ratio of voltage across the load (vo) given by, p= r/(1+r^2) io= 1/(1+r) vo=...

Intro It is December 2021. You work as a financial analyst for Merck & Co. and are tasked with the due diligence on the proposed acquisition of a biotech startup. You estimated the following cash...

7. (4 points) You are participating in a draw with the probabilities given below. It's $1.50 to enter, with a 30% chance of getting your money back, and a 10% chance of getting your money back and...