Question: Define longitudinal and lateral strains.

Define longitudinal and lateral strains.

Step by Step Solution

★★★★★

3.43 Rating (156 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

Longitudinal strain and lateral strain are terms used to describe the deformation or change in shape ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

10 5 points Required information Use the following information for the Exercises below. (Algo) [The following information applies to the questions displayed below.] Arctica manufactures snowmobiles...

Q:

Poisson ratio is defined as: (a) Longitudinal stress/longitudinal strain (b) Longitudinal stress/lateral stress (c) Lateral strain/longitudinal strain (d) Lateral stress/lateral strain

Q:

Modulus of rigidity is defined as the ratio of: (a) Longitudinal stress and longitudinal strain (b) Lateral stress and lateral strain (c) Shear stress and shear strain (d) Any one of the above

Q:

The strain at a point consists of normal and shear streain components. To determine the average strain in the object: a . Add the shear and normal strains and divide by two b . The averare strain is...

Q:

Longitudinal and lateral strains are (a) Same in nature (b) Opposite in nature (c) Same in magnitude (d) None of the above

Q:

A rectangular block is subjected to a direct longitudinal compressive stress 1 . External pressures of intensity 2 and 3 are applied in the lateral directions perpendicular to the longitudinal...

Q:

1- For an airplane with the following information and following flight condition: a) Derive the longitudinal and lateral-directional state space model b) Derive the longitudinal and lateral...

Q:

Source: Roberto Leon, Department of Civil and Environmental Engineering, Virginia Tech, Blacksburg, VAThere are two distinct stages in a construction project involving concrete. The first stage...

Q:

Exercise 2 : Thin cylinder under pressure - dimension A thin cylinder of radius R , wall thickness t and length L is submitted to an internal pressure P . Radius r thickness t The 3 normal stresses...

Q:

Design of a PID Controller for an Aircraft Pitch System 5. Physical Setup: The equations governing the motion of an aircraft are a very complicated set of six nonlinear coupled differential...

Q:

Hypothetically one bacterial cell is placed into the nutrient broth in a test tube at noon. Its generation time is 20 minutes. By 2:00 pm, the size of the population of bacteria in the test tube is...

Q:

An exponential graph contains the points (-2, 2) and (2, 54). Find the exponential equation that fits this information. Show your setup, work, and final answer.

Q:

1 . X , Y and Z form a general partnership with cash contributions of $ 5 0 , 0 0 0 , $ 5 0 , 0 0 0 and $ 1 0 0 , 0 0 0 , respectively. The partnership agreement provides for the maintenance of...

Q:

Administration overheads are recorded as a percentage of (a) Works cost (b) Prime cost (c) Direct materials (d) Direct wages

Q:

It is impossible to construct an engine which while operating in a cycle produces no other effect to extract heat from a single reservoir and do equivalent amount of work. This refers to : (a)...

Q:

Which of the following is incorrect statement (a) Heat is not completely convertible into work (b) Energy can be transferred from one form to another automatically (c) Heat cannot flow automatically...

Q:

The Kelvin-Planks law states the principle of conservation of (a) Work (b) heat (c) mass (d) heat into work

Q:

Given the following, what are the company's cash flows from financing activities? Interest earned on overdue accounts receivable of 58736 Payment of dividends to preferred shareholders of $53782...

Q:

Q3 (Essential to cover) The optimal risky portfolio P* has an expected return of 12.5% and a standard deviation of 22%. The current risk-free rate in the market is 1.5%. a. Draw the capital...

Q:

Sales and Production Budgets Sonic Inc. manufactures two models of speakers, Rumble and Thunder. Based on the following production and sales data for June, prepare (a) a sales budget and (b) a...