Question: If a material is restricted to deform and heated, it will develop (a) Tensile stress (b) Compressive stress (d) Shear stress (d) No stress

If a material is restricted to deform and heated, it will develop

(a) Tensile stress

(b) Compressive stress

(d) Shear stress

(d) No stress

Step by Step Solution

★★★★★

3.42 Rating (155 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

The Tech Student Government Association (SGA) has several campus projects it undertakes each year and its primary source of funding to support these projects is a T-shirt sale in the fall for what is...

Q:

1. In what circumstances would you choose to use a dividend discount model rather than a free cash flow model to value a firm? 5. Jand, Inc., currently pays a dividend of $1.22, which is expected to...

Q:

Part2A, 2B, and Discussion I'll need answers, formulas, and work shown please. Part 2A Torsional Key Design Choose a key material from Table 02 above and document your choice of material and temper...

Q:

Image transcription text Course Project Overview Guidelines 1. Legibly write on each piece of paper V Your first and last names V The course and section number The assignment title The page number 2....

Q:

Design a sleeve and cotter joint to resist a tensile load of 5 0 kN . All parts of the joint are made of the same material with the following allowable stresses: Allowable tensile stress t = 9 0 MPa;...

Q:

Q.3 a cotter joint to support a load varying Design from 30 kN in compression to 30 kN in tension. The material used is carbon steel for which the be used. The following allowable stresses may load...

Q:

Example 1 . Design and draw a cotter joint to support a load varying from 3 0 kN in compression to 3 0 kN in tension. The material used is carbon steel for which the following allowable stresses may...

Q:

A uniform bar fixed at one end and is free to Imove at the other end. If the temperature of the rod increased by 'T', neglecting the gravity effects, the rod will develop (a) Tensile stress (b)...

Q:

i ) The critical stress intensity factor for a particular brittle ceramics is 1 . 5 MPa m and it s Poisson s ratio is 0 . 2 7 . A thin tensile specimen of the material has an edge crack. If the...

Q:

EMT 1 5 0 1 ASSESSMENT 4 0 2 SEPTEMBER 2 0 2 4 QUESTION 1 What are the main four main forces may act on a body material? Answer by using diagrams. ( 4 ) Define the following: 2 . 1 Load ( 2 ) 2 . 2...

Q:

Need summary for this . Make sure someone who understands it and summarize it in 2 pages with some summary of the data also Article history: The interactions of a 1/2{111} edge dislocation with a...

Q:

Find the value of 4a-d. a. a = log 13 b. b = 3.6a c. c = antilog b d. d = 133.6 e. Compare the values you found. Describe any relationship you see. f. Complete the statement "log ab = ? . g. This...

Q:

Calculate the work done in a reversible expansion of three moles of an ideal gas from pressure of 4 bar to 1 bar at 298K. (A)-10304 J (B) +10304 J (C)- 3435 J (D)-107.7 J

Q:

Listen If Alphabet reports higher - than - expected earnings per share ( EPS ) , what does that Indicate? The company generated higher revenue than expected The company spent too much on advertising...

Q:

What is a computer network? LO.1

Q:

What is a draft tube? Why is it used in a reaction turbine? Describe with a neat sketch.

Q:

Pelton wheels are used for minimum heads of: (a) \(20 \mathrm{~m}\) (b) \(100 \mathrm{~m}\) (c) \(125 \mathrm{~m}\) (d) \(180 \mathrm{~m}\)

Q:

A double acting reciprocating pump has a piston of \(400 \mathrm{~mm}\) diameter and piston rod of \(40 \mathrm{~mm}\) diameter. Stroke length is \(300 \mathrm{~mm}\) and speed is \(60...

Q:

You deposit $10,000 annually into a life insurance fund for the next 12 years, after which time you plan to retire. a. If the deposits are made at the beginning of the year and earn an interest rate...

Q:

Question: What is the net advantage to leasing? An auto dealer is trying to decide whether to lease or buy new equipment for polishing vehicles. Cost of the equipment : $22,000.00 Useful life :...

Q:

Consider the three stocks in the following table. t represents price at time tr and Qt represents shares outstanding at time t. Stock C splits two-for-one in the last period. Required: Calculate the...