Question: Use Transfer Function blocks to construct a Simulink model to plot the solution of the following equations for 0 t 2 where f(t)

Use Transfer Function blocks to construct a Simulink model to plot the solution of the following equations for 0 ≤ t ≤ 2

 3x + 15i + 18x = f(t) x(0) = i(0) = 0 2y + 16ý + 50y = x(t) y(0) = y(0) = 0


where f(t) = 50us(t). At the output of the first block there is a saturation that limits |x| to be ≤ 1. This limits the input to the second block.

3x + 15i + 18x = f(t) x(0) = i(0) = 0 2y + 16 + 50y = x(t) y(0) = y(0) = 0

Step by Step Solution

★★★★★

3.43 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

To create a Simulink model for the given system youll need to set up transfer function blocks that r... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

Construct a Simulink model to plot the solution of the following equation for 0

Q:

Construct a Simulink model to plot the solution of the following equation for 0 t 4. 2 + 12 + 10x2 = 5 sin 0.8t x(0) = (0) = 0

Q:

Construct a Simulink model to plot the solution of the following equations for 0 t 2 where f(t) = 3t. Use the Ramp block in the Sources library. ij = -6x1 + 4x2 i2 = 5x - 7x, +f(t)

Q:

Use Transfer Function blocks to construct a Simulink model to plot the solution of the following equations for 0 t 2. where f(t) = 75u s (t). 3* + 15x + 18x = f(t) x(0) = i(0) = 0 2 + 16y + 50y =...

Q:

Use the Transfer Function block to construct a Simulink model to plot the solution of the following equation for 0 t 4. 2x + 12i + 10x Su,(t) Su,(t 2) x(0) = i(0) = 0

Q:

Use the Transfer Function block to construct a Simulink model to plot the solution of the following equation for 0 t 4. 2 + I2 + 10x2 = 5us(t) - 5us(t - 2) x(0) = (0) = 0

Q:

Construct a Simulink model to plot the solution of the following equations for 0 t 3 where f 1 (t) is a step function of height 3 starting at t = 0 and f 2 (t) is a step function of height -3...

Q:

Question II-A, The motion of a two-mass suspension model. (20 Marks) Consider the two-mass suspension model shown in Figure II-A.1. The equations of motion are: m* + (C + )x + (k + k)x C*-Kx = 0 M +...

Q:

Ovenview In this lab we will first learn how to implement transfer function in both Matlab and in Simulink. Next we show how to write block diagrams as signal flow graphs, and lastly we will use the...

Q:

IT IS POSSIBLE TO USE CODES ALONG WITH ODE SOLVERS IN SIMULINK. SO, THE SOLUTION CAN BE PREPARED IN SIMULINK BUT WITHOUT ANY CIRCUIT ELEMENTS. all the circuit designs, equations, codes, plots, and...

Q:

Show that the second equation in (12.126) can be expressed in terms of the field tensor Fv as follows: Answer: -y cos -y sin 0 -yB cosp (y cos + sin ) (y-1) sino cos 0 -y sin o 0 (y - 1) sino cos 0...

Q:

A grower believes that one in five of his citrus trees are infected with the citrus red mite mentioned in Exercise 8.116. How large a sample should be taken if the grower wishes to estimate the...

Q:

2. Calculate how much higher U.S. labor productivity will be in the year 2028 (relative to 2008) if LO1 a. productivity continues to grow by 3.1 percent per year. b. productivity growth falls to 1.4...

Q:

3. What concerns might shoppers have about their privacy? How would you advise Stop & Shop management to respond to these concerns?

Q:

The torque ratio of a gearset is 0.75. The pinion gear has 36 teeth and a diametral pitch of 8. Determine the number of teeth on the output gear and the radii of both gears.

Q:

You are designing a geartrain with three spur gears: one input gear, one idler gear, and one output gear. The diametral pitch for the geartrain is 16. The diameter of the input gear needs to be twice...

Q:

The helical gears in the simple geartrain have teeth numbers as labeled (Figure P8.17). The central gear rotates at 125 rpm and drives the two output shafts. Determine the speeds and rotation...

Q:

Example 15: Draw a flowchart to receive a positive whole number and determine how many of its digits in odd positions are 7. For instance, if the input is 6475672, the output should be 1 because...

Q:

When using derivative for speculation and hedging, which of the following is FALSE? In the case of options contract, traders buy call option on the underlying asset when the trader's expected price...

Q:

11. (20 points) Walt exchanges land held for investment for an office building owned and used by Skyler in her business. The fair market value of Walt's land is $225,000 and his adjusted basis in the...