Question: Use the Transfer Function block to construct a Simulink model to plot the solution of the following equation for 0 t 4. 2x

Use the Transfer Function block to construct a Simulink model to plot the solution of the following equation for 0 ≤ t ≤ 4.

 2x + 12i + 10x Su,(t) – Su,(t – 2) x(0) = i(0) = 0

2x + 12i + 10x Su,(t) Su,(t 2) x(0) = i(0) = 0

Step by Step Solution

★★★★★

3.37 Rating (172 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer
Step: 1 Unlock

The given equation is 2x 12x 10x 5u t 5u t 2 Rewrite this in terms of from Laplace transform 2s 2 x ... View full answer

blur-text-image
Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock
Step: 3 Unlock

Students Have Also Explored These Related Introduction Mechanical Engineering Questions!

Q:

Use Transfer Function blocks to construct a Simulink model to plot the solution of the following equations for 0 t 2. where f(t) = 75u s (t). 3* + 15x + 18x = f(t) x(0) = i(0) = 0 2 + 16y + 50y =...

Q:

Construct a Simulink model to plot the solution of the following equation for 0 t 4. 2x + 12i + 10x? = 8 sin 0.8t x(0) = i(0) = 0 %3D

Q:

Use Transfer Function blocks to construct a Simulink model to plot the solution of the following equations for 0 t 2 where f (t) = 50u s (t). At the output of the first block there is a dead zone...

Q:

Use the Transfer Function block to construct a Simulink model to plot the solution of the following equation for 0 t 4. 2 + I2 + 10x2 = 5us(t) - 5us(t - 2) x(0) = (0) = 0

Q:

Ovenview In this lab we will first learn how to implement transfer function in both Matlab and in Simulink. Next we show how to write block diagrams as signal flow graphs, and lastly we will use the...

Q:

#3 1.4 Exercises 1. Use Simulink with the Step function block, the Continuous-Time Transfer Fcn block, and the Scope block shown, to simulate and display the output waveform vc of the RLC circuit...

Q:

#4 1.4 Exercises 1. Use Simulink with the Step function block, the Continuous-Time Transfer Fcn block, and the Scope block shown, to simulate and display the output waveform vc of the RLC circuit...

Q:

Step 1 . In MATLAB, type "simulink" in the command window. Then go to "Blank Model" and save the model as " RLC . " We are going to create the model show in Fig. 2 to model an RLC circuit with a...

Q:

help asap. please solve the last part which is part f in Simulink ( Matlab ). i tried to do it and i got error. please check it and take a screen shot including the exact steps. ( here's what i tried...

Q:

the response of the system depends on the poles of the transfer function. Create a block diagram in Simulink and use MATLAB to plot the response of the system to a pulse function with height of 0.03...

Q:

A sauna has 7.0m3 of air volume, and the temperature is 90oC. The air is perfectly dry. How much water (in kg) should be evaporated if we want to increase the relative humidity from 0% to 10%? (See...

Q:

You have two assets and must calculate their values today based on their different payment streams and appropriate required returns. Asset 1 has a required return of 15% and will produce a stream of...

Q:

19. The A-1 Corporation supplies airplane manufacturers with preformed sheet metal panels that are used on the exterior of aircraft. Manufacturing these panels requires only five sheet metalforming...

Q:

3. Was the introduction of the Monster Thickburger a good idea or an example of information leading to a wrong decision?

Q:

For the industrial robot in Problem P8.4, assume that the robot arm stops rotating about base A. However, the link BC begins to rotate about joint B. If link BC rotates 90 in 0.2 s, calculate the...

Q:

The driving disk spins at a constant 280 rpm clockwise (Figure P8.6). Determine the velocity of the connecting pin at A. Also, does the collar at B move with constant velocity? Explain your answer....

Q:

A gasoline-powered engine produces 15 hp as it drives a water pump at a construction site. If the engines speed is 450 rpm, determine the torque T that is transmitted from the output shaft of the...

Q:

Please answer all 6 24 - Section 6.3 Inference for a Difference in Prop tions Question130f19 -/1 E View Policies Current Attempt in Progress Pennsylvania Seniors Favorite Subject? Exercise 1.24...

Q:

Please explain how to solve, thank you. Rafael is an analyst at a wealth management firm. One of his clients holds a $10,000 portfolio that consists of four stocks. The investment allocation in the...

Q:

Moira's Fruit Wine is planning to expand the amount of wine bottle inventory they are holding, and are evaluating two plans to finance the additional inventory. The required additional financing for...