Question: For the bus seat bracket described in Problem 19 and shown in Figure P58, propose an alternate design for the bracket, different from that shown

For the bus seat bracket described in Problem 19 and shown in Figure P5–8, propose an alternate design for the bracket, different from that shown in the figure, to achieve a lighter design with a design factor of approximately 4.0.

Data in Figure P5–8.

175 mm Simple supports Load on bracket 450 mm - 60 mm - 12 mm Section A-A 275 mm Bracket

Step by Step Solution

★★★★★

3.41 Rating (154 Votes )

There are 3 Steps involved in it

1 Expert Approved Answer

Step: 1 Unlock

One way to achieve a lighter design for the bus seat bracket shown in Figure P58 with a design facto... View full answer

Question Has Been Solved by an Expert!

Get step-by-step solutions from verified subject matter experts

Step: 2 Unlock

Step: 3 Unlock

Students Have Also Explored These Related Machine Elements In Mechanical Design Questions!

The following information is obtained from the books of NoFair Corporation as of its fiscal year ended December 31, 2022. Prepare a corporate income statement in good form including the EPS section...

Managing Scope Changes Case Study Scope changes on a project can occur regardless of how well the project is planned or executed. Scope changes can be the result of something that was omitted during...

Refer to the scenario described in Problem 19 and the file HousingBubble. a. Consider the Pre-Crisis worksheet data. Partition the data into training (50 percent), validation (30 percent), and test...

Question 15 3 pts A part of a bracket in the seat assembly of a bus is shown in Figure P5-8. The load varies from 1450 to 140 N as passengers enter and exit the bus. The bracket is made from SAE 1020...

Case Summary Read the Discussion Assignment 1-1 on p.24 of the text Winning and Longevity. Select a health care entity to focus on, this could be a clinic or hospital of your choosing. Apply the case...

prepare graphs showing : (a) the daily output compared to design and effective capacity (b) cumulative output compared to cumulative design and effective capacity what do these tell us about the...

can i get a solution to this question please. Value: Document (include your file name) 15% of final grade How to complete: 1. Read the following Anniversary Party scheduling problem: As the project...

Hi, I am doing a project for derivatives class and I have some questions about a regression and Monte Carlo simulation that I need to come up with. So the goal is to hedge against CDS instruments by...

1. Briefly describe which view you found most convincing . Note: you need not believe in God to say which view you found most persuasive. (You may think of it this way: if someone where to try to...

Provide a summary technical report with your own words about Pipelined Execution which is also named as Instruction Level Parallelism, addressing mainly the following areas: 1. What is Pipelined...

Vraag 2 Question 2 Vind 'n ortogonale diagonalisering van die volgende matriks met behulp van Matlab: Find an orthogonal diagonalization of the following matrix by means of Matlab: C = 1 -3 -3 1 -2 1...

A drug company manufactured a drug used for the treatment of multiple sclerosis (MS), which also contained an ingredient that was effective in treating MS in virtually everyone who took the drug but...

5. Assume that a persons consumption of just the right amounts of pork and chicken is in equilibrium. We can conclude that the a. marginal utility of pork must equal the marginal utility of chicken....

=+Is the source (e.g ., a person, a regulation, a document) of the requirement identified?

In case of cycloidal tooth profile gears (a) the pressure angle is always constant through the contact (b) the path of contact is a straight line (c) the variation in centre distance affects the...

Two right-handed helical gears connect two shafts \(70^{\circ}\) apart. The larger gear has 50 teeth and the smaller 20. The centre distance is \(167 \mathrm{~mm}\). Determine the helix angle of the...

What is the law for velocity of sliding between a gear pair?

Why is stock-based compensation added to net income?

Using the Starbucks financial statements provided on Blackboard, calculate and interpret the days to collect ratio. Assume 20% of all sales are credit sales. STARBUCKS CORP 10-K Income Statement in...

Makupa Ltd. produces and sells product Beta. The product sells at Sh. 800 and has a variable manufacturing cost of Sh. 300 per unit. In addition, the company incurs costs as follows: Variable selling...